Difference between revisions of "iMX6 Rex Ultra Accessing and Testing Peripherals"
Jump to navigation
Jump to search
| (27 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | [[Category:iMX6 Rex Development | + | [[Category:iMX6 Rex Development Kit]] |
[[Category:iMX6 Rex Ultra]] | [[Category:iMX6 Rex Ultra]] | ||
[[Category:iMX6 Rex Peripherals]] | [[Category:iMX6 Rex Peripherals]] | ||
| Line 5: | Line 5: | ||
<div style="float:right">__TOC__</div> | <div style="float:right">__TOC__</div> | ||
| − | Elemental operations of iMX6 Rex Development | + | Elemental operations of iMX6 Rex Development Kit interfaces in Ultra configuration are shown on this page. |
== Prerequisites == | == Prerequisites == | ||
=== Hardware === | === Hardware === | ||
| − | * DC power supply ( | + | * DC power supply (12V, 1A) |
* iMX6 Rex Module Ultra | * iMX6 Rex Module Ultra | ||
| − | * iMX6 Rex | + | * iMX6 Rex Base Board |
=== Peripherals and Accessories === | === Peripherals and Accessories === | ||
| Line 34: | Line 34: | ||
'''''Output:''''' Audio chip is detected and bound as an input device | '''''Output:''''' Audio chip is detected and bound as an input device | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# dmesg | grep -i sgtl5000 |
sgtl5000 0-000a: sgtl5000 revision 0x11 | sgtl5000 0-000a: sgtl5000 revision 0x11 | ||
sgtl5000 0-000a: Using internal LDO instead of VDDD | sgtl5000 0-000a: Using internal LDO instead of VDDD | ||
| Line 44: | Line 44: | ||
'''''Output:''''' Card imx-audio-sgtl5000 is available | '''''Output:''''' Card imx-audio-sgtl5000 is available | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# alsamixer |
lqqqqqqqqqqqqqqqqqqqqqqqqqqqqq AlsaMixer v1.0.28 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk | lqqqqqqqqqqqqqqqqqqqqqqqqqqqqq AlsaMixer v1.0.28 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk | ||
x Card: imx-audio-sgtl5000 F1: Help x | x Card: imx-audio-sgtl5000 F1: Help x | ||
| Line 71: | Line 71: | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | '''''Input:''''' Boot-up module with HDMI cable plugged in, connect headphones into LINE_OUT connector and plug-in USB flash drive with | + | '''''Input:''''' Boot-up module with HDMI cable plugged in, connect headphones into LINE_OUT connector and plug-in USB flash drive with MP3 file<br /> |
'''''Output:''''' Sound is played and heard | '''''Output:''''' Sound is played and heard | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| Line 106: | Line 106: | ||
'''''Output:''''' GPIO register is read and displayed state of the button | '''''Output:''''' GPIO register is read and displayed state of the button | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# echo 511 > /sys/class/gpio/export |
| − | root@imx6- | + | root@imx6-rexultra:~# echo in > /sys/class/gpio/gpio511/direction |
| − | root@imx6- | + | root@imx6-rexultra:~# cat /sys/class/gpio/gpio511/value |
1 | 1 | ||
| − | root@imx6- | + | root@imx6-rexultra:~# cat /sys/class/gpio/gpio511/value |
0 | 0 | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
</syntaxhighlight> | </syntaxhighlight> | ||
| Line 134: | Line 123: | ||
CPU: Freescale i.MX6Q rev1.2 at 792 MHz | CPU: Freescale i.MX6Q rev1.2 at 792 MHz | ||
Reset cause: POR | Reset cause: POR | ||
| − | Board: MX6 Rex - | + | Board: MX6 Rex - ultra |
I2C: ready | I2C: ready | ||
DRAM: 2 GiB | DRAM: 2 GiB | ||
| Line 153: | Line 142: | ||
'''''Note:''''' MAC address should be identical with the address on the sticker placed on module | '''''Note:''''' MAC address should be identical with the address on the sticker placed on module | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# ip addr show dev eth0 |
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 | 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 | ||
link/ether 00:0d:15:00:cc:e2 brd ff:ff:ff:ff:ff:ff | link/ether 00:0d:15:00:cc:e2 brd ff:ff:ff:ff:ff:ff | ||
| Line 162: | Line 151: | ||
'''''Output:''''' IPv4 address is assigned | '''''Output:''''' IPv4 address is assigned | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# dmesg | tail |
... | ... | ||
libphy: 2188000.ethernet:03 - Link is Up - 100/Full | libphy: 2188000.ethernet:03 - Link is Up - 100/Full | ||
| Line 169: | Line 158: | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# udhcpc -i eth0 |
udhcpc (v1.22.1) started | udhcpc (v1.22.1) started | ||
Sending discover... | Sending discover... | ||
| Line 177: | Line 166: | ||
== HDMI Output == | == HDMI Output == | ||
| − | '''''Input:''''' Connect LCD monitor to | + | '''''Input:''''' Connect LCD monitor to the base board<br /> |
| − | '''''Output:''''' Desktop UI is correctly | + | '''''Output:''''' Desktop UI is displayed correctly<br /> |
| − | [[image: | + | [[image:iMX6_TinyRex_Development_Kit-HDMI_terminal.png|580px]] |
== I2C == | == I2C == | ||
| Line 186: | Line 175: | ||
* SGTL5000 audio (0x0A) | * SGTL5000 audio (0x0A) | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# i2cdetect -y 0 |
0 1 2 3 4 5 6 7 8 9 a b c d e f | 0 1 2 3 4 5 6 7 8 9 a b c d e f | ||
00: -- -- -- -- -- -- -- UU -- -- -- -- -- | 00: -- -- -- -- -- -- -- UU -- -- -- -- -- | ||
| Line 207: | Line 196: | ||
'''''Note:''''' HDMI monitor must be disconnected otherwise I2C bus 1 scanning bus might freeze. | '''''Note:''''' HDMI monitor must be disconnected otherwise I2C bus 1 scanning bus might freeze. | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# i2cdetect -y 1 |
0 1 2 3 4 5 6 7 8 9 a b c d e f | 0 1 2 3 4 5 6 7 8 9 a b c d e f | ||
00: -- -- -- -- -- -- -- -- -- -- -- -- -- | 00: -- -- -- -- -- -- -- -- -- -- -- -- -- | ||
| Line 222: | Line 211: | ||
'''''Output:''''' I2C bus 2 is allocated for external use via System Header<br /> | '''''Output:''''' I2C bus 2 is allocated for external use via System Header<br /> | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# i2cdetect -y 2 |
0 1 2 3 4 5 6 7 8 9 a b c d e f | 0 1 2 3 4 5 6 7 8 9 a b c d e f | ||
00: -- -- -- -- -- -- -- -- -- -- -- -- -- | 00: -- -- -- -- -- -- -- -- -- -- -- -- -- | ||
| Line 237: | Line 226: | ||
'''''Output:''''' GPIO expander is detected | '''''Output:''''' GPIO expander is detected | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "1-0027" > /sys/bus/i2c/drivers/pca953x/unbind |
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "1-0027" > /sys/bus/i2c/drivers/pca953x/bind |
pca953x 1-0027: interrupt support not compiled in | pca953x 1-0027: interrupt support not compiled in | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| Line 245: | Line 234: | ||
'''''Output:''''' RTC is detected | '''''Output:''''' RTC is detected | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "1-0051" > /sys/bus/i2c/drivers/rtc-pcf8563/unbind |
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "1-0051" > /sys/bus/i2c/drivers/rtc-pcf8563/bind |
rtc-pcf8563 1-0051: chip found, driver version 0.4.3 | rtc-pcf8563 1-0051: chip found, driver version 0.4.3 | ||
rtc-pcf8563 1-0051: low voltage detected, date/time is not reliable. | rtc-pcf8563 1-0051: low voltage detected, date/time is not reliable. | ||
| Line 257: | Line 246: | ||
'''''Output:''''' I2C EEPROM is detected | '''''Output:''''' I2C EEPROM is detected | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "1-0057" > /sys/bus/i2c/drivers/at24/unbind |
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "1-0057" > /sys/bus/i2c/drivers/at24/bind |
at24 1-0057: 256 byte 24c02 EEPROM, writable, 1 bytes/write | at24 1-0057: 256 byte 24c02 EEPROM, writable, 1 bytes/write | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | '''''Input:''''' Write and | + | '''''Input:''''' Write and read data from I2C EEPROM<br /> |
'''''Output:''''' If successful, console text 'Data are the same' should appear | '''''Output:''''' If successful, console text 'Data are the same' should appear | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "0123" > eeprom_in |
| − | root@imx6- | + | root@imx6-rexultra:~# cat eeprom_in > /sys/bus/i2c/devices/1-0057/eeprom |
| − | root@imx6- | + | root@imx6-rexultra:~# head -c 4 /sys/bus/i2c/devices/1-0057/eeprom > eeprom_out |
| − | root@imx6- | + | root@imx6-rexultra:~# diff eeprom_in eeprom_out && echo "Data are the same" |
Data are the same | Data are the same | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | === | + | === Alternative test === |
'''''Input:''''' List I2C bus 0, 1 and 2<br /> | '''''Input:''''' List I2C bus 0, 1 and 2<br /> | ||
'''''Output:''''' Available devices are displayed | '''''Output:''''' Available devices are displayed | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# ls /sys/bus/i2c/devices/i2c-0 | grep ^[0] |
0-000a | 0-000a | ||
| − | root@imx6- | + | root@imx6-rexultra:~# ls /sys/bus/i2c/devices/i2c-1 | grep ^[1] |
1-0048 | 1-0048 | ||
1-0050 | 1-0050 | ||
| − | root@imx6- | + | root@imx6-rexultra:~# ls /sys/bus/i2c/devices/i2c-2 | grep ^[2] |
</syntaxhighlight> | </syntaxhighlight> | ||
| Line 288: | Line 277: | ||
'''''Output:''''' Red LED assembled on module switches from ON to OFF state with heartbeat pulses afterwards | '''''Output:''''' Red LED assembled on module switches from ON to OFF state with heartbeat pulses afterwards | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "none" > /sys/devices/soc0/leds*/leds/module-led/trigger |
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "1" > /sys/devices/soc0/leds*/leds/module-led/brightness |
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "0" > /sys/devices/soc0/leds*/leds/module-led/brightness |
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "heartbeat" > /sys/devices/soc0/leds*/leds/module-led/trigger |
</syntaxhighlight> | </syntaxhighlight> | ||
'''''Input:''''' GPIO expander PCA9535 driver<br /> | '''''Input:''''' GPIO expander PCA9535 driver<br /> | ||
| − | '''''Output:''''' Red LED assembled on | + | '''''Output:''''' Red LED assembled on the base board switches from ON to OFF state |
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# echo 510 > /sys/class/gpio/export |
| − | root@imx6- | + | root@imx6-rexultra:~# echo out > /sys/class/gpio/gpio510/direction |
| − | root@imx6- | + | root@imx6-rexultra:~# echo 1 > /sys/class/gpio/gpio510/value |
| − | root@imx6- | + | root@imx6-rexultra:~# echo 0 > /sys/class/gpio/gpio510/value |
</syntaxhighlight> | </syntaxhighlight> | ||
== LVDS display == | == LVDS display == | ||
Details how to properly connect display with LVDS and touchsreen interfaces are described on [[iMX6 Rex Display Set|Display Set page]].<br /><br /> | Details how to properly connect display with LVDS and touchsreen interfaces are described on [[iMX6 Rex Display Set|Display Set page]].<br /><br /> | ||
| − | '''''Input:''''' Configure | + | '''''Input:''''' Configure U-Boot video environment and boot up the module<br /> |
'''''Output:''''' GUI can be seen on LVDS screen | '''''Output:''''' GUI can be seen on LVDS screen | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| Line 314: | Line 303: | ||
== DDR memory == | == DDR memory == | ||
'''''Input:''''' None<br /> | '''''Input:''''' None<br /> | ||
| − | '''''Output:''''' Memory test passes without any | + | '''''Output:''''' Memory test passes without any errors |
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# memtester 2G 1 |
memtester version 4.1.3 (32-bit) | memtester version 4.1.3 (32-bit) | ||
Copyright (C) 2010 Charles Cazabon. | Copyright (C) 2010 Charles Cazabon. | ||
| Line 394: | Line 383: | ||
== PCI Express == | == PCI Express == | ||
| − | The procedure uses | + | The procedure uses a WiFi wireless card to test PCIe interface. More details concerning wireless cards are located on [[iMX6 Rex Wireless|WiFi and Bluetooth Cards page]] .<br/><br /> |
'''''Input:''''' Plug Wireless WiFi Link 4965AGN mini PCIe card into mini PCIe slot 1<br /> | '''''Input:''''' Plug Wireless WiFi Link 4965AGN mini PCIe card into mini PCIe slot 1<br /> | ||
'''''Output:''''' Card is detected by system | '''''Output:''''' Card is detected by system | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# lspci |
00:00.0 PCI bridge: Device 16c3:abcd (rev 01) | 00:00.0 PCI bridge: Device 16c3:abcd (rev 01) | ||
01:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61) | 01:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61) | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | '''''Input:''''' Plug Wireless WiFi Link 4965AGN mini PCIe card into mini PCIe slot<br /> | + | '''''Input:''''' Plug Wireless WiFi Link 4965AGN mini PCIe card into mini PCIe slot 1<br /> |
'''''Output:''''' Wireless WiFi card firmware is loaded | '''''Output:''''' Wireless WiFi card firmware is loaded | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# dmesg | grep iwl4965 |
iwl4965: Intel(R) Wireless WiFi 4965 driver for Linux, in-tree: | iwl4965: Intel(R) Wireless WiFi 4965 driver for Linux, in-tree: | ||
iwl4965: Copyright(c) 2003-2011 Intel Corporation | iwl4965: Copyright(c) 2003-2011 Intel Corporation | ||
| Line 416: | Line 405: | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | '''''Input:''''' Plug Wireless WiFi Link 4965AGN mini PCIe card into mini PCIe slot<br /> | + | '''''Input:''''' Plug Wireless WiFi Link 4965AGN mini PCIe card into mini PCIe slot 1<br /> |
'''''Output:''''' Card scans neighbour networks | '''''Output:''''' Card scans neighbour networks | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# rfkill unblock wlan |
| − | root@imx6- | + | root@imx6-rexultra:~# ip link set wlan0 up |
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready | IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready | ||
| − | root@imx6- | + | root@imx6-rexultra:~# iw dev wlan0 scan |
BSS 20:aa:4b:7e:21:97(on wlan0) | BSS 20:aa:4b:7e:21:97(on wlan0) | ||
TSF: 9263203904202 usec (107d, 05:06:43) | TSF: 9263203904202 usec (107d, 05:06:43) | ||
| Line 453: | Line 442: | ||
=== Alternative test === | === Alternative test === | ||
| − | '''''Input:''''' Plug Wireless WiFi Link 4965AGN mini PCIe card into mini PCIe slot<br /> | + | '''''Input:''''' Plug Wireless WiFi Link 4965AGN mini PCIe card into mini PCIe slot 1<br /> |
'''''Output:''''' Card scans neighbour networks | '''''Output:''''' Card scans neighbour networks | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# ip link set wlan0 up |
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready | IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready | ||
| − | root@imx6- | + | root@imx6-rexultra:~# iwlist wlan0 scan |
wlan0 Scan completed : | wlan0 Scan completed : | ||
Cell 01 - Address: 20:AA:4B:7E:21:97 | Cell 01 - Address: 20:AA:4B:7E:21:97 | ||
| Line 488: | Line 477: | ||
== SATA == | == SATA == | ||
| − | '''''Input:''''' Power off the | + | '''''Input:''''' Power off the base board, connect HDD to SATA connector, provide power for the hard drive and turn on the board<br /> |
'''''Output:''''' HDD is detected | '''''Output:''''' HDD is detected | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| Line 505: | Line 494: | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | SATA device can be used as a default | + | SATA device can be used as a default filesystem source. [[iMX6 Rex SATA|SATA Interface page]] contains detailed steps to follow. iMX6 Rex Deveploment Kit gives an alternate option of utilizing SATA interface and reliabale storage by supporting [[iMX6 Rex CFast Card|CFast Cards]]. |
== SD card == | == SD card == | ||
| Line 513: | Line 502: | ||
'''''Output:''''' Kernel log shows that mmc1 device is added and removed | '''''Output:''''' Kernel log shows that mmc1 device is added and removed | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# dmesg | tail |
... | ... | ||
mmc1: new high speed SDHC card at address e624 | mmc1: new high speed SDHC card at address e624 | ||
| Line 528: | Line 517: | ||
'''''Output:''''' Module boots up successfully | '''''Output:''''' Module boots up successfully | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# dmesg | grep -i "Kernel command line" |
Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk2p2 rootwait rw | Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk2p2 rootwait rw | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| Line 536: | Line 525: | ||
'''''Output:''''' SPI Flash sst25vf016b(sst25vf032b) is detected | '''''Output:''''' SPI Flash sst25vf016b(sst25vf032b) is detected | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "spi2.0" > /sys/bus/spi/drivers/m25p80/unbind |
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "spi2.0" > /sys/bus/spi/drivers/m25p80/bind |
m25p80 spi2.0: found sst25vf032b, expected m25p32 | m25p80 spi2.0: found sst25vf032b, expected m25p32 | ||
m25p80 spi2.0: sst25vf032b (4096 Kbytes) | m25p80 spi2.0: sst25vf032b (4096 Kbytes) | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | '''''Input:''''' Write and | + | '''''Input:''''' Write and read data from M25P80 flash<br /> |
'''''Output:''''' If successful, console text 'Data are the same' should appear | '''''Output:''''' If successful, console text 'Data are the same' should appear | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# echo -n "0123" > mtd_in |
| − | root@imx6- | + | root@imx6-rexultra:~# mtd_debug write /dev/mtd0 0 4 mtd_in |
Copied 4 bytes from mtd_in to address 0x00000000 in flash | Copied 4 bytes from mtd_in to address 0x00000000 in flash | ||
| − | root@imx6- | + | root@imx6-rexultra:~# mtd_debug read /dev/mtd0 0 4 mtd_out |
Copied 4 bytes from address 0x00000000 in flash to mtd_out | Copied 4 bytes from address 0x00000000 in flash to mtd_out | ||
| − | root@imx6- | + | root@imx6-rexultra:~# diff mtd_in mtd_out && echo "Data are the same" |
Data are the same | Data are the same | ||
</syntaxhighlight> | </syntaxhighlight> | ||
== UART serial console == | == UART serial console == | ||
| − | '''''Input:''''' Connect RS-232 cable into | + | '''''Input:''''' Connect RS-232 cable into the base board connector and open serial console with baud rate 115200 8n1<br /> |
'''''Output:''''' The board is controlled and responsive to serial terminal commands | '''''Output:''''' The board is controlled and responsive to serial terminal commands | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# uname -a |
| − | Linux imx6- | + | Linux imx6-rexultra 3.14.58-yocto+g11e5ba3 #1 SMP PREEMPT Sun Mar 13 20:20:31 CET 2016 armv7l GNU/Linux |
</syntaxhighlight> | </syntaxhighlight> | ||
== USB == | == USB == | ||
| − | '''''Input:''''' Plug USB flash drive with single VFAT partition into bottom USB connector<br /> | + | '''''Input:''''' Plug USB flash drive with single VFAT partition into the bottom USB connector<br /> |
'''''Output:''''' Filesystem recognises the flash drive and automatically mounts it. SMC Hub with ID 0424:2514 is mounted | '''''Output:''''' Filesystem recognises the flash drive and automatically mounts it. SMC Hub with ID 0424:2514 is mounted | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| Line 581: | Line 570: | ||
'''''Output:''''' Generated file and copied file have the same checksum | '''''Output:''''' Generated file and copied file have the same checksum | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# rm -f file.txt /run/media/sda1/file.txt |
| − | root@imx6- | + | root@imx6-rexultra:~# dd if=/dev/urandom of=file.txt count=1024 bs=1024 |
1024+0 records in | 1024+0 records in | ||
1024+0 records out | 1024+0 records out | ||
1048576 bytes (1.0 MB) copied, 0.435456 s, 2.4 MB/s | 1048576 bytes (1.0 MB) copied, 0.435456 s, 2.4 MB/s | ||
| − | root@imx6- | + | root@imx6-rexultra:~# cp file.txt /run/media/sda1/ |
| − | root@imx6- | + | root@imx6-rexultra:~# md5sum file.txt /run/media/sda1/file.txt |
33ef96efccbbf570bfce477735ed2068 file.txt | 33ef96efccbbf570bfce477735ed2068 file.txt | ||
33ef96efccbbf570bfce477735ed2068 /run/media/sda1/file.txt | 33ef96efccbbf570bfce477735ed2068 /run/media/sda1/file.txt | ||
| − | root@imx6- | + | root@imx6-rexultra:~# rm file.txt /run/media/sda1/file.txt |
</syntaxhighlight> | </syntaxhighlight> | ||
== USB OTG == | == USB OTG == | ||
| − | '''''Input:''''' Load USB serial gadget driver and connect | + | '''''Input:''''' Load USB serial gadget driver and connect base board to host PC over micro USB cable<br /> |
'''''Output:''''' Driver is successfully loaded and host PC detects a new USB serial gadget device<br /><br /> | '''''Output:''''' Driver is successfully loaded and host PC detects a new USB serial gadget device<br /><br /> | ||
| − | iMX6 Rex Development | + | iMX6 Rex Development Kit: |
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | root@imx6- | + | root@imx6-rexultra:~# modprobe -i g_serial |
g_serial gadget: Gadget Serial v2.4 | g_serial gadget: Gadget Serial v2.4 | ||
g_serial gadget: g_serial ready | g_serial gadget: g_serial ready | ||
| − | root@imx6- | + | root@imx6-rexultra:~# g_serial gadget: high-speed config #2: CDC ACM config |
</syntaxhighlight> | </syntaxhighlight> | ||
| Line 611: | Line 600: | ||
Bus 001 Device 014: ID 0525:a4a7 Netchip Technology, Inc. Linux-USB Serial Gadget (CDC ACM mode) | Bus 001 Device 014: ID 0525:a4a7 Netchip Technology, Inc. Linux-USB Serial Gadget (CDC ACM mode) | ||
... | ... | ||
| + | </syntaxhighlight> | ||
| + | |||
| + | == Touchscreen == | ||
| + | Details how to properly connect display with LVDS and touchsreen interfaces are described on [[iMX6 Rex Display Set|Display Set page]].<br /><br /> | ||
| + | |||
| + | '''''Input:''''' Search kernel log for TSC2007 chip<br /> | ||
| + | '''''Output:''''' TSC2007 chip is detected and bound as an input device | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | root@imx6-rexultra:~# dmesg | grep -i tsc2007 | ||
| + | input: TSC2007 Touchscreen as /devices/soc0/soc.0/2100000.aips-bus/21a4000.i2c/i2c-1/1-0048/input/input0 | ||
| + | evbug: Connected device: input0 (TSC2007 Touchscreen at 1-0048/input0) | ||
| + | </syntaxhighlight> | ||
| + | |||
| + | '''''Input:''''' Press the touchscreen<br /> | ||
| + | '''''Output:''''' Touchscreen events are generated | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | root@imx6-rexultra:~# evtest /dev/input/by-path/platform-21a4000.i2c-event | ||
| + | Input driver version is 1.0.1 | ||
| + | Input device ID: bus 0x18 vendor 0x0 product 0x0 version 0x0 | ||
| + | Input device name: "TSC2007 Touchscreen" | ||
| + | Supported events: | ||
| + | Event type 0 (EV_SYN) | ||
| + | Event type 1 (EV_KEY) | ||
| + | Event code 330 (BTN_TOUCH) | ||
| + | Event type 3 (EV_ABS) | ||
| + | Event code 0 (ABS_X) | ||
| + | Value 3529 | ||
| + | Min 0 | ||
| + | Max 4095 | ||
| + | Event code 1 (ABS_Y) | ||
| + | Value 375 | ||
| + | Min 0 | ||
| + | Max 4095 | ||
| + | Event code 24 (ABS_PRESSURE) | ||
| + | Value 0 | ||
| + | Min 0 | ||
| + | Max 4095 | ||
| + | Properties: | ||
| + | Testing ... (interrupt to exit) | ||
| + | Event: time 1457899907.959665, type 1 (EV_KEY), code 330 (BTN_TOUCH), value 1 | ||
| + | Event: time 1457899907.959665, type 3 (EV_ABS), code 0 (ABS_X), value 1657 | ||
| + | Event: time 1457899907.959665, type 3 (EV_ABS), code 1 (ABS_Y), value 2486 | ||
| + | Event: time 1457899907.959665, type 3 (EV_ABS), code 24 (ABS_PRESSURE), value 3268 | ||
| + | Event: time 1457899907.959665, -------------- EV_SYN ------------ | ||
| + | Event: time 1457899907.969094, type 1 (EV_KEY), code 330 (BTN_TOUCH), value 0 | ||
| + | Event: time 1457899907.969094, type 3 (EV_ABS), code 24 (ABS_PRESSURE), value 0 | ||
| + | Event: time 1457899907.969094, -------------- EV_SYN ------------ | ||
| + | </syntaxhighlight> | ||
| + | |||
| + | === Alternative test === | ||
| + | '''''Input:''''' Press the touchscreen<br /> | ||
| + | '''''Output:''''' Touchscreen events are generated | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | root@imx6-rexultra:~# hexdump -C /dev/input/event0 | ||
| + | 00000000 79 ca e5 56 cd a3 07 00 01 00 4a 01 01 00 00 00 |y..V......J.....| | ||
| + | 00000010 79 ca e5 56 cd a3 07 00 03 00 00 00 2f 08 00 00 |y..V......../...| | ||
| + | 00000020 79 ca e5 56 cd a3 07 00 03 00 01 00 a7 07 00 00 |y..V............| | ||
| + | 00000030 79 ca e5 56 cd a3 07 00 03 00 18 00 64 06 00 00 |y..V........d...| | ||
| + | 00000040 79 ca e5 56 cd a3 07 00 00 00 00 00 00 00 00 00 |y..V............| | ||
| + | 00000050 79 ca e5 56 a7 c4 07 00 01 00 4a 01 00 00 00 00 |y..V......J.....| | ||
| + | 00000060 79 ca e5 56 a7 c4 07 00 03 00 18 00 00 00 00 00 |y..V............| | ||
| + | 00000070 79 ca e5 56 a7 c4 07 00 00 00 00 00 00 00 00 00 |y..V............| | ||
</syntaxhighlight> | </syntaxhighlight> | ||
Latest revision as of 10:51, 24 April 2022
Elemental operations of iMX6 Rex Development Kit interfaces in Ultra configuration are shown on this page.
Prerequisites
Hardware
- DC power supply (12V, 1A)
- iMX6 Rex Module Ultra
- iMX6 Rex Base Board
Peripherals and Accessories
- 1x FullHD monitor with Audio output
- 1x LVDS touchscreen display
- 2x MicroSD card
- 1x MiniPCIe WiFi card
- 1x MiniPCIe 3G card
- 1x SATA HDD drive
- 2x USB FLASH drive
- 1x headphones
- 1x microphone
Cables
- Ethernet cable
- HDMI cable
- Micro USB cable
- RS-232 cable
Audio
Input: Search kernel log for SGTL5000 chip
Output: Audio chip is detected and bound as an input device
root@imx6-rexultra:~# dmesg | grep -i sgtl5000 sgtl5000 0-000a: sgtl5000 revision 0x11 sgtl5000 0-000a: Using internal LDO instead of VDDD imx-sgtl5000 sound.23: sgtl5000 <-> 2028000.ssi mapping ok #0: imx-audio-sgtl5000
Input: Run alsamixer command
Output: Card imx-audio-sgtl5000 is available
root@imx6-rexultra:~# alsamixer lqqqqqqqqqqqqqqqqqqqqqqqqqqqqq AlsaMixer v1.0.28 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk x Card: imx-audio-sgtl5000 F1: Help x x Chip: F2: System information x x View: F3:[Playback] F4: Capture F5: All F6: Select sound card x x Item: Headphone [dB gain: -20.00, -20.00] Esc: Exit x x x x lqqk lqqk lqqk x x x x x x x x x x x x x x x x x x x x x x x x x x x x xaax x x x x x x xaax x x x x x x xaax x x x x x x xaax x x x x x x xaax x x x x x x xaax x x x x xaax xaax x x x x xaax xaax x x x x mqqj DAC lqqk mqqj mqqj lqqk MIC_IN lqqk x x xOOx xMMx xOOx x x mqqj mqqj mqqj x x 23<>23 75<>75 0 x x <Headphon>Headphon Headphon PCM Mic Capture Capture Capture x mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj
Input: Boot-up module with HDMI cable plugged in, connect headphones into LINE_OUT connector and plug-in USB flash drive with MP3 file
Output: Sound is played and heard
root@imx6-rexultra:~# aplay -D sysdefault:CARD=sgtl5000audio multimedia/sample.wav #root@imx6-rexultra:~# aplay -D sysdefault:CARD=imxaudiosgtl500 multimedia/sample.wav Playing WAVE 'multimedia/sample.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
root@imx6-rexultra:~# aplay -D sysdefault:CARD=imxhdmisoc multimedia/sample.wav Playing WAVE 'multimedia/sample.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
Input: Plug headphones into HEADPHONES connector and mic into MICROPHONE connector
Output: Microphone sound is played in headphones
root@imx6-rexultra:~# arecord -D sysdefault:CARD=sgtl5000audio -t wav -f cd | aplay -D sysdefault:CARD=imxaudiosgtl500 #root@imx6-rexultra:~# arecord -D sysdefault:CARD=imxaudiosgtl500 -t wav -f cd | aplay -D sysdefault:CARD=imxaudiosgtl500
Input: Plug headphones into HEADPHONES connector and mic into MICROPHONE connector
Output: Sound is recorded and played afterwards
root@imx6-rexultra:~# arecord -D sysdefault:CARD=sgtl5000audio -t wav -f cd -d 10 multimedia/recorded.wav #root@imx6-rexultra:~# arecord -D sysdefault:CARD=imxaudiosgtl500 -t wav -f cd -d 10 multimedia/recorded.wav Recording WAVE 'multimedia/recorded.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo root@imx6-rexultra:~# aplay -D sysdefault:CARD=sgtl5000audio multimedia/recorded.wav #root@imx6-rexultra:~# aplay -D sysdefault:CARD=imxaudiosgtl500 multimedia/recorded.wav Playing WAVE 'multimedia/recorded.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
User button
Input: Press and hold USER button (pca9535 driver is used)
Output: GPIO register is read and displayed state of the button
root@imx6-rexultra:~# echo 511 > /sys/class/gpio/export root@imx6-rexultra:~# echo in > /sys/class/gpio/gpio511/direction root@imx6-rexultra:~# cat /sys/class/gpio/gpio511/value 1 root@imx6-rexultra:~# cat /sys/class/gpio/gpio511/value 0
Reset button
Input: Press the RESET button
Output: Module will execute bootloader immediately with "Reset cause: POR"
Note: Module should never freeze or hang after the reset button was pressed. Testing the operation 10 times gives a reliable result
U-Boot 2014.10-dirty (Mar 12 2016 - 11:34:54) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: MX6 Rex - ultra I2C: ready DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 SF: Detected SST25VF032B with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0
Ethernet
Input: None
Output: Device driver is available
Note: MAC address should be identical with the address on the sticker placed on module
root@imx6-rexultra:~# ip addr show dev eth0
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:0d:15:00:cc:e2 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20d:15ff:fe00:cce2/64 scope link
Input: Plug Ethernet cable into connector and issue DHCP command
Output: IPv4 address is assigned
root@imx6-rexultra:~# dmesg | tail ... libphy: 2188000.ethernet:03 - Link is Up - 100/Full IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
root@imx6-rexultra:~# udhcpc -i eth0 udhcpc (v1.22.1) started Sending discover... Sending select for 192.168.0.178... Lease of 192.168.0.178 obtained, lease time 600
HDMI Output
Input: Connect LCD monitor to the base board
Output: Desktop UI is displayed correctly
I2C
Input: Scan I2C bus 0
Output: Available devices:
- SGTL5000 audio (0x0A)
root@imx6-rexultra:~# i2cdetect -y 0
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- UU -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Input: Scan I2C bus 1
Output: Available devices:
- GPIO expander (0x27)
- touchscreen TSC2007 (0x48)
- HDMI Output EDID (0x50)
- RTC clock (0x51)
- EEPROM (0x57)
Note: HDMI monitor must be disconnected otherwise I2C bus 1 scanning bus might freeze.
root@imx6-rexultra:~# i2cdetect -y 1
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- 18 -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- UU -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- UU -- -- -- -- -- -- --
50: UU UU -- -- -- -- -- UU -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Input: Scan I2C bus 2
Output: I2C bus 2 is allocated for external use via System Header
root@imx6-rexultra:~# i2cdetect -y 2
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Input: Trigger I2C GPIO expander detection.
Output: GPIO expander is detected
root@imx6-rexultra:~# echo -n "1-0027" > /sys/bus/i2c/drivers/pca953x/unbind root@imx6-rexultra:~# echo -n "1-0027" > /sys/bus/i2c/drivers/pca953x/bind pca953x 1-0027: interrupt support not compiled in
Input: Trigger I2C RTC detection
Output: RTC is detected
root@imx6-rexultra:~# echo -n "1-0051" > /sys/bus/i2c/drivers/rtc-pcf8563/unbind root@imx6-rexultra:~# echo -n "1-0051" > /sys/bus/i2c/drivers/rtc-pcf8563/bind rtc-pcf8563 1-0051: chip found, driver version 0.4.3 rtc-pcf8563 1-0051: low voltage detected, date/time is not reliable. rtc-pcf8563 1-0051: low voltage detected, date/time is not reliable. rtc rtc1: invalid alarm value: 2030-10-20 41:58:0 rtc-pcf8563 1-0051: rtc core: registered rtc-pcf8563 as rtc1
Input: Trigger I2C EEPROM detection
Output: I2C EEPROM is detected
root@imx6-rexultra:~# echo -n "1-0057" > /sys/bus/i2c/drivers/at24/unbind root@imx6-rexultra:~# echo -n "1-0057" > /sys/bus/i2c/drivers/at24/bind at24 1-0057: 256 byte 24c02 EEPROM, writable, 1 bytes/write
Input: Write and read data from I2C EEPROM
Output: If successful, console text 'Data are the same' should appear
root@imx6-rexultra:~# echo -n "0123" > eeprom_in root@imx6-rexultra:~# cat eeprom_in > /sys/bus/i2c/devices/1-0057/eeprom root@imx6-rexultra:~# head -c 4 /sys/bus/i2c/devices/1-0057/eeprom > eeprom_out root@imx6-rexultra:~# diff eeprom_in eeprom_out && echo "Data are the same" Data are the same
Alternative test
Input: List I2C bus 0, 1 and 2
Output: Available devices are displayed
root@imx6-rexultra:~# ls /sys/bus/i2c/devices/i2c-0 | grep ^[0] 0-000a root@imx6-rexultra:~# ls /sys/bus/i2c/devices/i2c-1 | grep ^[1] 1-0048 1-0050 root@imx6-rexultra:~# ls /sys/bus/i2c/devices/i2c-2 | grep ^[2]
User LED
Input: None
Output: Red LED assembled on module switches from ON to OFF state with heartbeat pulses afterwards
root@imx6-rexultra:~# echo -n "none" > /sys/devices/soc0/leds*/leds/module-led/trigger root@imx6-rexultra:~# echo -n "1" > /sys/devices/soc0/leds*/leds/module-led/brightness root@imx6-rexultra:~# echo -n "0" > /sys/devices/soc0/leds*/leds/module-led/brightness root@imx6-rexultra:~# echo -n "heartbeat" > /sys/devices/soc0/leds*/leds/module-led/trigger
Input: GPIO expander PCA9535 driver
Output: Red LED assembled on the base board switches from ON to OFF state
root@imx6-rexultra:~# echo 510 > /sys/class/gpio/export root@imx6-rexultra:~# echo out > /sys/class/gpio/gpio510/direction root@imx6-rexultra:~# echo 1 > /sys/class/gpio/gpio510/value root@imx6-rexultra:~# echo 0 > /sys/class/gpio/gpio510/value
LVDS display
Details how to properly connect display with LVDS and touchsreen interfaces are described on Display Set page.
Input: Configure U-Boot video environment and boot up the module
Output: GUI can be seen on LVDS screen
Rex U-Boot > setenv video 'video=mxcfb0:dev=ldb,edt570,if=RGB666 video=mxcfb1:off' Rex U-Boot > boot
DDR memory
Input: None
Output: Memory test passes without any errors
root@imx6-rexultra:~# memtester 2G 1 memtester version 4.1.3 (32-bit) Copyright (C) 2010 Charles Cazabon. Licensed under the GNU General Public License version 2 (only). pagesize is 4096 pagesizemask is 0xfffff000 want 2048MB (2147483648 bytes) got 267MB (280412160 bytes), trying mlock ...locked. Loop 1/1: Stuck Address : ok Random Value : ok Compare XOR : ok Compare SUB : ok Compare MUL : ok Compare DIV : ok Compare OR : ok Compare AND : ok Sequential Increment: ok Solid Bits : ok Block Sequential : ok Checkerboard : ok Bit Spread : ok Bit Flip : ok Walking Ones : ok Walking Zeroes : ok Done.
Further information about DDR3 memories and its calibration can be accessed in Memory Calibration details.
Modem
Input: Plug HE910 3G card into PCIe mini 2 slot and plug SIM card into SIM1 slot
Output: HE910 3G card is detected and AT commands executed
root@imx6-rexultra:~# lsusb | grep -i 1bc7 Bus 001 Device 003: ID 1bc7:0021 Telit HE910
root@imx6-rexultra:~# cat > /etc/minirc.he910 << EOF pu port /dev/ttyACM0 pu baudrate 115200 pu bits 8 pu parity N pu stopbits 1 pu rtscts No pu xonxoff No pu escape-key ^B EOF root@imx6-rexultra:~# echo "Press 'Ctrl+B z q' to exit" root@imx6-rexultra:~# minicom -o he910 AT AT+CPIN? AT+CREG? AT+COPS?
Log:
AT OK AT+CPIN? +CPIN: READY OK AT+CREG? +CREG: 0,1 OK AT+COPS? +COPS: 0,0,"Vodafone",0 OK
PCI Express
The procedure uses a WiFi wireless card to test PCIe interface. More details concerning wireless cards are located on WiFi and Bluetooth Cards page .
Input: Plug Wireless WiFi Link 4965AGN mini PCIe card into mini PCIe slot 1
Output: Card is detected by system
root@imx6-rexultra:~# lspci 00:00.0 PCI bridge: Device 16c3:abcd (rev 01) 01:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
Input: Plug Wireless WiFi Link 4965AGN mini PCIe card into mini PCIe slot 1
Output: Wireless WiFi card firmware is loaded
root@imx6-rexultra:~# dmesg | grep iwl4965 iwl4965: Intel(R) Wireless WiFi 4965 driver for Linux, in-tree: iwl4965: Copyright(c) 2003-2011 Intel Corporation iwl4965 0000:01:00.0: Detected Intel(R) Wireless WiFi Link 4965AGN, REV=0x4 iwl4965 0000:01:00.0: device EEPROM VER=0x36, CALIB=0x5 iwl4965 0000:01:00.0: Tunable channels: 13 802.11bg, 19 802.11a channels iwl4965 0000:01:00.0: loaded firmware version 228.61.2.24
Input: Plug Wireless WiFi Link 4965AGN mini PCIe card into mini PCIe slot 1
Output: Card scans neighbour networks
root@imx6-rexultra:~# rfkill unblock wlan
root@imx6-rexultra:~# ip link set wlan0 up
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
root@imx6-rexultra:~# iw dev wlan0 scan
BSS 20:aa:4b:7e:21:97(on wlan0)
TSF: 9263203904202 usec (107d, 05:06:43)
freq: 5220
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble (0x0031)
signal: -69.00 dBm
last seen: 0 ms ago
SSID: OpenWrt5g
Supported rates: 6.0* 9.0 12.0* 18.0 24.0* 36.0 48.0 54.0
DS Parameter set: channel 44
Country: CZ Environment: Indoor/Outdoor
Channels [36 - 48] @ 23 dBm
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
WPA: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
Extended capabilities: 6
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
Alternative test
Input: Plug Wireless WiFi Link 4965AGN mini PCIe card into mini PCIe slot 1
Output: Card scans neighbour networks
root@imx6-rexultra:~# ip link set wlan0 up
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
root@imx6-rexultra:~# iwlist wlan0 scan
wlan0 Scan completed :
Cell 01 - Address: 20:AA:4B:7E:21:97
Channel:44
Frequency:5.22 GHz (Channel 44)
Quality=39/70 Signal level=-71 dBm
Encryption key:on
ESSID:"OpenWrt5g"
Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s
36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=0000086d2e342cf9
Extra: Last beacon: 40ms ago
IE: Unknown: 00094F70656E5772743567
IE: Unknown: 01088C129824B048606C
IE: Unknown: 03012C
IE: Unknown: 0706435A20240417
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: WPA Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: Unknown: 7F080000000000000040
IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
SATA
Input: Power off the base board, connect HDD to SATA connector, provide power for the hard drive and turn on the board
Output: HDD is detected
root@imx6-rexultra:~# dmesg | grep -i -e sata -e ata1 ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 306 ata1: SATA link down (SStatus 0 SControl 300) ahci-imx 2200000.sata: no device found, disabling link. ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug
SATA device can be used as a default filesystem source. SATA Interface page contains detailed steps to follow. iMX6 Rex Deveploment Kit gives an alternate option of utilizing SATA interface and reliabale storage by supporting CFast Cards.
SD card
Top slot SD card (mmcblk1)
Input: Plug and unplug SD card
Output: Kernel log shows that mmc1 device is added and removed
root@imx6-rexultra:~# dmesg | tail ... mmc1: new high speed SDHC card at address e624 mmcblk1: mmc1:e624 SU08G 7.40 GiB mmcblk1: p1 p2 FAT-fs (mmcblk1p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. EXT4-fs (mmcblk1p2): recovery complete EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) mmc1: card e624 removed
Bottom slot SD card (mmcblk2)
Input: Plug SD card with a filesystem and boot-up the module
Output: Module boots up successfully
root@imx6-rexultra:~# dmesg | grep -i "Kernel command line" Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk2p2 rootwait rw
SPI Flash Memory
Input: Trigger M25P80 flash detection
Output: SPI Flash sst25vf016b(sst25vf032b) is detected
root@imx6-rexultra:~# echo -n "spi2.0" > /sys/bus/spi/drivers/m25p80/unbind root@imx6-rexultra:~# echo -n "spi2.0" > /sys/bus/spi/drivers/m25p80/bind m25p80 spi2.0: found sst25vf032b, expected m25p32 m25p80 spi2.0: sst25vf032b (4096 Kbytes)
Input: Write and read data from M25P80 flash
Output: If successful, console text 'Data are the same' should appear
root@imx6-rexultra:~# echo -n "0123" > mtd_in root@imx6-rexultra:~# mtd_debug write /dev/mtd0 0 4 mtd_in Copied 4 bytes from mtd_in to address 0x00000000 in flash root@imx6-rexultra:~# mtd_debug read /dev/mtd0 0 4 mtd_out Copied 4 bytes from address 0x00000000 in flash to mtd_out root@imx6-rexultra:~# diff mtd_in mtd_out && echo "Data are the same" Data are the same
UART serial console
Input: Connect RS-232 cable into the base board connector and open serial console with baud rate 115200 8n1
Output: The board is controlled and responsive to serial terminal commands
root@imx6-rexultra:~# uname -a Linux imx6-rexultra 3.14.58-yocto+g11e5ba3 #1 SMP PREEMPT Sun Mar 13 20:20:31 CET 2016 armv7l GNU/Linux
USB
Input: Plug USB flash drive with single VFAT partition into the bottom USB connector
Output: Filesystem recognises the flash drive and automatically mounts it. SMC Hub with ID 0424:2514 is mounted
root@imx6-rexultra:~# lsusb Bus 001 Device 003: ID 1bc7:0021 Telit HE910 Bus 001 Device 005: ID 054c:0243 Sony Corp. MicroVault Flash Drive Bus 001 Device 004: ID 0930:6544 Toshiba Corp. Kingston DataTraveler 2.0 Stick (2GB) Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@imx6-rexultra:~# mount | grep /run/media/sd* /dev/sda1 on /run/media/sda1 type vfat (rw,relatime,gid=6,fmask=0007,dmask=0007,allow_utime=0020,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro)
Input: Generate a dummy file and copy it into USB flash drive
Output: Generated file and copied file have the same checksum
root@imx6-rexultra:~# rm -f file.txt /run/media/sda1/file.txt root@imx6-rexultra:~# dd if=/dev/urandom of=file.txt count=1024 bs=1024 1024+0 records in 1024+0 records out 1048576 bytes (1.0 MB) copied, 0.435456 s, 2.4 MB/s root@imx6-rexultra:~# cp file.txt /run/media/sda1/ root@imx6-rexultra:~# md5sum file.txt /run/media/sda1/file.txt 33ef96efccbbf570bfce477735ed2068 file.txt 33ef96efccbbf570bfce477735ed2068 /run/media/sda1/file.txt root@imx6-rexultra:~# rm file.txt /run/media/sda1/file.txt
USB OTG
Input: Load USB serial gadget driver and connect base board to host PC over micro USB cable
Output: Driver is successfully loaded and host PC detects a new USB serial gadget device
iMX6 Rex Development Kit:
root@imx6-rexultra:~# modprobe -i g_serial g_serial gadget: Gadget Serial v2.4 g_serial gadget: g_serial ready root@imx6-rexultra:~# g_serial gadget: high-speed config #2: CDC ACM config
Host PC:
user@voipac:~$ lsusb ... Bus 001 Device 014: ID 0525:a4a7 Netchip Technology, Inc. Linux-USB Serial Gadget (CDC ACM mode) ...
Touchscreen
Details how to properly connect display with LVDS and touchsreen interfaces are described on Display Set page.
Input: Search kernel log for TSC2007 chip
Output: TSC2007 chip is detected and bound as an input device
root@imx6-rexultra:~# dmesg | grep -i tsc2007 input: TSC2007 Touchscreen as /devices/soc0/soc.0/2100000.aips-bus/21a4000.i2c/i2c-1/1-0048/input/input0 evbug: Connected device: input0 (TSC2007 Touchscreen at 1-0048/input0)
Input: Press the touchscreen
Output: Touchscreen events are generated
root@imx6-rexultra:~# evtest /dev/input/by-path/platform-21a4000.i2c-event
Input driver version is 1.0.1
Input device ID: bus 0x18 vendor 0x0 product 0x0 version 0x0
Input device name: "TSC2007 Touchscreen"
Supported events:
Event type 0 (EV_SYN)
Event type 1 (EV_KEY)
Event code 330 (BTN_TOUCH)
Event type 3 (EV_ABS)
Event code 0 (ABS_X)
Value 3529
Min 0
Max 4095
Event code 1 (ABS_Y)
Value 375
Min 0
Max 4095
Event code 24 (ABS_PRESSURE)
Value 0
Min 0
Max 4095
Properties:
Testing ... (interrupt to exit)
Event: time 1457899907.959665, type 1 (EV_KEY), code 330 (BTN_TOUCH), value 1
Event: time 1457899907.959665, type 3 (EV_ABS), code 0 (ABS_X), value 1657
Event: time 1457899907.959665, type 3 (EV_ABS), code 1 (ABS_Y), value 2486
Event: time 1457899907.959665, type 3 (EV_ABS), code 24 (ABS_PRESSURE), value 3268
Event: time 1457899907.959665, -------------- EV_SYN ------------
Event: time 1457899907.969094, type 1 (EV_KEY), code 330 (BTN_TOUCH), value 0
Event: time 1457899907.969094, type 3 (EV_ABS), code 24 (ABS_PRESSURE), value 0
Event: time 1457899907.969094, -------------- EV_SYN ------------
Alternative test
Input: Press the touchscreen
Output: Touchscreen events are generated
root@imx6-rexultra:~# hexdump -C /dev/input/event0 00000000 79 ca e5 56 cd a3 07 00 01 00 4a 01 01 00 00 00 |y..V......J.....| 00000010 79 ca e5 56 cd a3 07 00 03 00 00 00 2f 08 00 00 |y..V......../...| 00000020 79 ca e5 56 cd a3 07 00 03 00 01 00 a7 07 00 00 |y..V............| 00000030 79 ca e5 56 cd a3 07 00 03 00 18 00 64 06 00 00 |y..V........d...| 00000040 79 ca e5 56 cd a3 07 00 00 00 00 00 00 00 00 00 |y..V............| 00000050 79 ca e5 56 a7 c4 07 00 01 00 4a 01 00 00 00 00 |y..V......J.....| 00000060 79 ca e5 56 a7 c4 07 00 03 00 18 00 00 00 00 00 |y..V............| 00000070 79 ca e5 56 a7 c4 07 00 00 00 00 00 00 00 00 00 |y..V............|