iMX8M Industrial Accessing and Testing Peripherals
Revision as of 08:44, 17 January 2022 by Voipac-sw (talk | contribs) (→Peripherals and Accessories)
Elemental operations of iMX8M Industrial Development Kit interfaces in Max configuration are shown on this page.
Prerequisites
Hardware
- DC power supply (5V, 4A)
- iMX8M Industrial Development Kit Max
Peripherals and Accessories
- 1x FullHD monitor with Audio output
- 1x MicroSD card
- 1x MiniPCIe WiFi card
- 1x MiniPCIe 3G card
- 1x RPi camera module
- 2x USB FLASH drive
Cables
- Ethernet cable
- HDMI cable
- Micro USB cable
- USB to UART cable
- Headphones
Audio
Input: Search kernel log for SGTL5000 chip
Output: Audio chip is detected and bound as an input device
root@imx6-openrexultra:~# dmesg | grep -i sgtl5000 sgtl5000 1-000a: sgtl5000 revision 0x11 sgtl5000 1-000a: Using internal LDO instead of VDDD imx-sgtl5000 sound-sgtl5000: sgtl5000 <-> 2028000.ssi mapping ok #0: imx-audio-sgtl5000
Input: Run alsamixer command
Output: Card imx-audio-sgtl5000 is available
root@imx6-openrexultra:~# alsamixer lqqqqqqqqqqqqqqqqqqqqqqqqqqqqq AlsaMixer v1.0.29 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk x Card: imx-audio-sgtl5000 F1: Help x x Chip: F2: System information x x View: F3:[Playback] F4: Capture F5: All F6: Select sound card x x Item: Headphone [dB gain: -19.00, -20.00] Esc: Exit x x x x lqqk lqqk lqqk x x x x x x x x x x x x x x x x x x x x x x x x x x x x xaax x x x x x x xaax x x x x x x xaax x x x x x x xaax x x x x x x xaax x x x x xa x xaax x x x x xaax xaax x x x x xaax xaax x x x x mqqj DAC lqqk mqqj mqqj lqqk MIC_IN lqqk x x xOOx xMMx xOOx x x mqqj mqqj mqqj x x 24<>23 75<>75 0 x x <Headphon>Headphon Headphon PCM Mic Capture Capture Capture x mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj
Input: Boot-up the board with HDMI cable plugged in, connect headphones into HP_OUT connector and plug-in USB flash drive with MP3 file on it
Output: Sound is played and heard
root@imx6-openrexultra:~# aplay multimedia/sample.wav Playing WAVE 'multimedia/sample.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
root@imx6-openrexultra:~# #aplay -D sysdefault:CARD=imxaudiosgtl500 multimedia/sample.wav root@imx6-openrexultra:~# aplay -D sysdefault:CARD=sgtl5000audio multimedia/sample.wav Playing WAVE 'multimedia/sample.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
root@imx6-openrexultra:~# aplay -D sysdefault:CARD=imxhdmisoc multimedia/sample.wav Playing WAVE 'multimedia/sample.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
Input: Plug headphones with microphone input into HP_OUT connector
Output: Microphone sound is played in headphones
root@imx6-openrexultra:~# #arecord -D sysdefault:CARD=imxaudiosgtl500 -t wav -f cd | aplay -D sysdefault:CARD=imxaudiosgtl500 root@imx6-openrexultra:~# arecord -D sysdefault:CARD=sgtl5000audio -t wav -f cd | aplay -D sysdefault:CARD=sgtl5000audio
Input: Plug headphones with microphone input into HP_OUT connector
Output: Sound is recorded and played afterwards
root@imx6-openrexultra:~# #arecord -D sysdefault:CARD=imxaudiosgtl500 -t wav -f cd -d 10 multimedia/recorded.wav root@imx6-openrexultra:~# arecord -D sysdefault:CARD=sgtl5000audio -t wav -f cd -d 10 multimedia/recorded.wav Recording WAVE 'multimedia/recorded.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo root@imx6-openrexultra:~# #aplay -D sysdefault:CARD=imxaudiosgtl500 multimedia/recorded.wav root@imx6-openrexultra:~# aplay -D sysdefault:CARD=sgtl5000audio multimedia/recorded.wav Playing WAVE 'multimedia/recorded.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
User button
Input: Press Home/Back-/Menu+ buttons
Output: Button events 1 and 0 are generated
root@imx6-openrexultra:~# evtest /dev/input/by-path/platform-gpio-keys*-event
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "gpio-keys"
Supported events:
Event type 0 (EV_SYN)
Event type 1 (EV_KEY)
Event code 102 (KEY_HOME)
Event code 139 (KEY_MENU)
Event code 158 (KEY_BACK)
Properties:
Testing ... (interrupt to exit)
Event: time 1473952105.010541, type 1 (EV_KEY), code 102 (KEY_HOME), value 1
Event: time 1473952105.010541, -------------- SYN_REPORT ------------
Event: time 1473952105.140569, type 1 (EV_KEY), code 102 (KEY_HOME), value 0
Event: time 1473952105.140569, -------------- SYN_REPORT ------------
Event: time 1473952106.320588, type 1 (EV_KEY), code 158 (KEY_BACK), value 1
Event: time 1473952106.320588, -------------- SYN_REPORT ------------
Event: time 1473952106.440540, type 1 (EV_KEY), code 158 (KEY_BACK), value 0
Event: time 1473952106.440540, -------------- SYN_REPORT ------------
Event: time 1473952109.630544, type 1 (EV_KEY), code 139 (KEY_MENU), value 1
Event: time 1473952109.630544, -------------- SYN_REPORT ------------
Event: time 1473952109.760589, type 1 (EV_KEY), code 139 (KEY_MENU), value 0
Event: time 1473952109.760589, -------------- SYN_REPORT ------------
Alternative test
Input: Press Home/Back-/Menu+ buttons
Output: Button events 1 and 0 are generated
root@imx6-openrexultra:~# hexdump -C /dev/input/by-path/platform-gpio-keys-event 00000000 ef e7 da 57 ca 8e 0a 00 01 00 66 00 01 00 00 00 |...W......f.....| 00000010 ef e7 da 57 ca 8e 0a 00 00 00 00 00 00 00 00 00 |...W............| 00000020 ef e7 da 57 9f b1 0c 00 01 00 66 00 00 00 00 00 |...W......f.....| 00000030 ef e7 da 57 9f b1 0c 00 00 00 00 00 00 00 00 00 |...W............| 00000040 f0 e7 da 57 28 70 06 00 01 00 9e 00 01 00 00 00 |...W(p..........| 00000050 f0 e7 da 57 28 70 06 00 00 00 00 00 00 00 00 00 |...W(p..........| 00000060 f0 e7 da 57 18 93 08 00 01 00 9e 00 00 00 00 00 |...W............| 00000070 f0 e7 da 57 18 93 08 00 00 00 00 00 00 00 00 00 |...W............| 00000080 f1 e7 da 57 69 78 02 00 01 00 8b 00 01 00 00 00 |...Wix..........| 00000090 f1 e7 da 57 69 78 02 00 00 00 00 00 00 00 00 00 |...Wix..........| 000000a0 f1 e7 da 57 68 9b 04 00 01 00 8b 00 00 00 00 00 |...Wh...........| 000000b0 f1 e7 da 57 68 9b 04 00 00 00 00 00 00 00 00 00 |...Wh...........|
Reset button
Input: Press the RESET button
Output: The board will execute bootloader immediately with "Reset cause: POR"
Note: iMX8M Industrial Development Kit should never freeze or hang after the reset button was pressed. Testing the operation 10 times gives a reliable result
U-Boot 2015.10+fslc+g7d8ddd7 (Dec 15 2016 - 18:52:24 +0100) CPU: Freescale i.MX6QUAD rev1.1 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 44C Reset cause: POR Board: iMX6-OpenRex I2C: ready DRAM: 512 MiB MMC: FSL_SDHC: 0 SF: Detected SST26VF032B with page size 256 Bytes, erase size 4 KiB, total 4 MiB In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 OpenRex U-Boot>
CAN
Input: None
Output: Device driver is available
root@imx6-openrexultra:~# ip addr show dev can0
2: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN group default qlen 10
link/can
root@imx6-openrexultra:~# ip addr show dev can1
3: can1: <NOARP,ECHO> mtu 16 qdisc noop state DOWN group default qlen 10
link/can
Camera Input
Input: Connect RPi camera module into CSI interface and check if it is detected on I2C bus
Output: I2C address 0x36 is occupied and under use
Note: HDMI monitor may cause I2C communication issues
root@imx6-openrexultra:~# i2cdetect -y 1
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- UU -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- UU -- -- -- -- -- -- -- -- --
40: UU -- -- -- -- -- -- -- UU -- -- -- -- -- -- --
50: UU -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Input: Connect RPi camera into CSI interface and check kernel modules
Output: Device driver ov5647_camera_mipi_int(or ov5647_camera_mipi) is loaded
root@imx6-openrexultra:~# lsmod Module Size Used by mxc_v4l2_capture 27362 1 ipu_bg_overlay_sdc 5230 1 mxc_v4l2_capture ipu_still 2304 1 mxc_v4l2_capture ipu_prp_enc 5864 1 mxc_v4l2_capture ipu_csi_enc 3807 1 mxc_v4l2_capture ipu_fg_overlay_sdc 6056 1 mxc_v4l2_capture lm75 4768 0 sht21 2126 0 ov5647_camera_mipi_int 30415 0 v4l2_int_device 2897 3 ov5647_camera_mipi_int,ipu_csi_enc,mxc_v4l2_capture at24 5488 0 fxas2100x 6680 0 fxos8700 9014 0 mxc_dcic 6536 0 iwl4965 88394 0 iwlegacy 62850 1 iwl4965 galcore 226429 2
Input: Connect RPi camera module into CSI interface and capture image
Output: The image is displayed on HDMI monitor
root@imx6-openrexultra:~# echo 2 > /sys/bus/i2c/devices/1-0036/ov5647_mode root@imx6-openrexultra:~# gst-launch-1.0 v4l2src device="/dev/video0" ! video/x-bayer,width=1920,height=1080,framerate=30/1 ! queue ! bayer2rgb ! videoconvert ! fbdevsink Setting pipeline to PAUSED ... Pipeline is live and does not need PREROLL ... Setting pipeline to PLAYING ... New clock: GstSystemClock ERROR: v4l2 capture: unsupported ioctrl! ERROR: v4l2 capture: unsupported ioctrl! WARNING: from element /GstPipeline:pipeline0/GstFBDEVSink:fbdevsink0: A lot of buffers are being dropped. Additional debug info: /home/marek/workdir/imx6/yocto/fsl-release-bsp-4.1/build-x11/tmp/work/cortexa9hf-vfp-neon-poky-linux-gnueabi/gstreamer1.0/1.6.0-r0/gstreamer-1.6.0/libs/gst/base/gstbasesink.c(2846): gst_base_sink_is_too_la: There may be a timestamping problem, or this computer is too slow. mxc_hdmi 20e0000.hdmi_video: Read EDID again mxc_hdmi 20e0000.hdmi_video: create default modelist EVENT plugin WARNING: from element /GstPipeline:pipeline0/GstFBDEVSink:fbdevsink0: A lot of buffers are being dropped. Additional debug info: /home/marek/workdir/imx6/yocto/fsl-release-bsp-4.1/build-x11/tmp/work/cortexa9hf-vfp-neon-poky-linux-gnueabi/gstreamer1.0/1.6.0-r0/gstreamer-1.6.0/libs/gst/base/gstbasesink.c(2846): gst_base_sink_is_too_la: There may be a timestamping problem, or this computer is too slow. ^Chandling interrupt. Interrupt: Stopping pipeline ... Execution ended after 0:00:27.103901670 Setting pipeline to PAUSED ... Setting pipeline to READY ... Setting pipeline to NULL ... Freeing pipeline ... power_down_callback: ipu0/csi1
Alternative test
Input: Connect RPi camera module into CSI interface and capture image
Output: The image is displayed on HDMI monitor
root@imx6-openrexultra:~# echo 1 > /sys/bus/i2c/devices/1-0036/ov5647_mode root@imx6-openrexultra:~# gst-launch-1.0 v4l2src device="/dev/video0" ! video/x-bayer,width=1280,height=720,framerate=30/1 ! queue ! bayer2rgb ! videoconvert ! fbdevsink Setting pipeline to PAUSED ... Pipeline is live and does not need PREROLL ... Setting pipeline to PLAYING ... New clock: GstSystemClock ERROR: v4l2 capture: unsupported ioctrl! ERROR: v4l2 capture: unsupported ioctrl! WARNING: from element /GstPipeline:pipeline0/GstFBDEVSink:fbdevsink0: A lot of buffers are being dropped. Additional debug info: /home/marek/workdir/imx6/yocto/fsl-release-bsp-4.1/build-x11/tmp/work/cortexa9hf-vfp-neon-poky-linux-gnueabi/gstreamer1.0/1.6.0-r0/gstreamer-1.6.0/libs/gst/base/gstbasesink.c(2846): gst_base_sink_is_too_la: There may be a timestamping problem, or this computer is too slow. ^Chandling interrupt. Interrupt: Stopping pipeline ... Execution ended after 0:00:06.514209667 Setting pipeline to PAUSED ... Setting pipeline to READY ... Setting pipeline to NULL ... Freeing pipeline ... root@imx6-openrexultra:~# power_down_callback: ipu0/csi1
Software integration and additional commands or settings of CSI camera interface are available on separate iMX6 OpenRex Camera page.
Ethernet
Input: None
Output: Device driver is available
Note: MAC address should be identical with the address on the sticker placed on the board
root@imx6-openrexultra:~# ip addr show dev eth0
4: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:0d:15:00:d1:75 brd ff:ff:ff:ff:ff:ff
Input: Plug Ethernet cable into connector and issue DHCP command
Output: IPv4 address is assigned
root@imx6-openrexultra:~# dmesg | tail ... fec 2188000.ethernet eth0: Link is Down fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
root@imx6-openrexultra:~# udhcpc -i eth0 udhcpc (v1.23.2) started Sending discover... Sending discover... Sending select for 192.168.1.39... Lease of 192.168.1.39 obtained, lease time 600 /etc/udhcpc.d/50default: Adding DNS 192.168.1.1 /etc/udhcpc.d/50default: Adding DNS 192.168.1.2
HDMI Output
Input: Connect LCD monitor to the SBC
Output: Desktop UI is displayed correctly
I2C
Input: Scan I2C bus 0
Output: Available devices:
- PMIC control (0x08)
- Compass + Accelerometer FXOS8700 (0x1C)
- Gyroscope FXAS21002 (0x20)
- EEPROM (0x50/0x57)
root@imx6-openrexultra:~# i2cdetect -y 0
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- UU -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- UU -- -- --
20: UU -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: UU UU UU UU UU UU UU UU -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Input: Scan I2C bus 1
Output: Available devices:
- Audio SGTL5000 (0x0A)
- CSI Camera (0x36)
- Humidity sensor SHT21 (0x40)
- Temperature sensor TMP101 (0x48)
- HDMI Output EDID (0x50)
root@imx6-openrexultra:~# i2cdetect -y 1
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- UU -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- UU -- -- -- -- -- -- -- -- --
40: UU -- -- -- -- -- -- -- UU -- -- -- -- -- -- --
50: UU -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Input: Scan I2C bus 2
Output: This I2C bus is reserved for external use and accessible via connectors
root@imx6-openrexultra:~# i2cdetect -y 2
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Input: Trigger I2C EEPROM detection
Output: I2C EEPROM is detected
root@imx6-openrexultra:~# echo -n "0-0050" > /sys/bus/i2c/drivers/at24/unbind root@imx6-openrexultra:~# echo -n "0-0050" > /sys/bus/i2c/drivers/at24/bind at24 0-0050: 2048 byte 24c16 EEPROM, writable, 1 bytes/write
Input: Write and read data from I2C EEPROM
Output: If successful, console text 'Data are the same' should appear
root@imx6-openrexultra:~# echo -n "0123" > eeprom_in root@imx6-openrexultra:~# cat eeprom_in > /sys/bus/i2c/devices/0-0050/eeprom root@imx6-openrexultra:~# head -c 4 /sys/bus/i2c/devices/0-0050/eeprom > eeprom_out root@imx6-openrexultra:~# diff eeprom_in eeprom_out && echo "Data are the same" Data are the same
Altarnative test
Input: List I2C bus 0, 1 and 2
Output: Available devices are displayed
root@imx6-openrexultra:~# ls /sys/bus/i2c/devices/i2c-0 | grep ^[0] 0-0008 0-001c 0-0020 0-0050 0-0051 0-0052 0-0053 0-0054 0-0055 0-0056 0-0057
Sensors
Input: Test Compass, Accelerometer (FXOS8700) and Gyroscope (FXAS21002) sensors
Output: Sensors are registered by the Linux kernel
root@imx6-openrexultra:~# echo 1 > /sys/devices/virtual/misc/FreescaleAccelerometer/enable root@imx6-openrexultra:~# echo 1 > /sys/devices/virtual/misc/FreescaleMagnetometer/enable root@imx6-openrexultra:~# echo 1 > /sys/devices/virtual/misc/FreescaleGyroscope/enable misc FreescaleGyroscope: mma enable setting active root@imx6-openrexultra:~# evtest No device specified, trying to scan all of /dev/input/event* Available devices: /dev/input/event0: gpio_ir_recv /dev/input/event1: MCE IR Keyboard/Mouse (gpio-rc-recv) /dev/input/event2: gpio-keys /dev/input/event3: fxos8700 /dev/input/event4: fxas2100x Select the device event number [0-4]: 3 ... root@imx6-openrexultra:~# evtest No device specified, trying to scan all of /dev/input/event* Available devices: /dev/input/event0: gpio_ir_recv /dev/input/event1: MCE IR Keyboard/Mouse (gpio-rc-recv) /dev/input/event2: gpio-keys /dev/input/event3: fxos8700 /dev/input/event4: fxas2100x Select the device event number [0-4]: 4 ... root@imx6-openrexultra:~# echo 0 > /sys/devices/virtual/misc/FreescaleAccelerometer/enable root@imx6-openrexultra:~# echo 0 > /sys/devices/virtual/misc/FreescaleMagnetometer/enable root@imx6-openrexultra:~# echo 0 > /sys/devices/virtual/misc/FreescaleGyroscope/enable
Input: Test SHT21 humidity sensor
Output: Sensor provides actual humidity and temperature values
root@imx6-openrexultra:~# cat /sys/devices/soc0/soc/2100000.aips-bus/21a4000.i2c/i2c-1/1-0040/hwmon/hwmon*/humidity1_input 20741 root@imx6-openrexultra:~# cat /sys/devices/soc0/soc/2100000.aips-bus/21a4000.i2c/i2c-1/1-0040/hwmon/hwmon*/temp1_input 30853
Input: Test TMP101 temperature sensor
Output: Sensor provides current temperature readout
root@imx6-openrexultra:~# cat /sys/devices/soc0/soc/2100000.aips-bus/21a4000.i2c/i2c-1/1-0048/hwmon/hwmon*/temp1_input 32125
Infrared receiver
Input: Press Infrared remote keys. (For Samsung Infrared remote load "nec" protocol)
Output: Events are detected
root@imx6-openrexultra:~# echo nec > /sys/devices/soc0/ir-receiver/rc/rc0/protocols
root@imx6-openrexultra:~# evtest /dev/input/by-path/platform-ir-receiver-event
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "gpio_ir_recv"
Supported events:
Event type 0 (EV_SYN)
Event type 1 (EV_KEY)
Event code 152 (KEY_SCREENLOCK)
Event type 4 (EV_MSC)
Event code 4 (MSC_SCAN)
Key repeat handling:
Repeat type 20 (EV_REP)
Repeat code 0 (REP_DELAY)
Value 500
Repeat code 1 (REP_PERIOD)
Value 125
Properties:
Testing ... (interrupt to exit)
Event: time 1474009071.488894, type 4 (EV_MSC), code 4 (MSC_SCAN), value 70707
Event: time 1474009071.488894, -------------- SYN_REPORT ------------
Event: time 1474009072.178245, type 4 (EV_MSC), code 4 (MSC_SCAN), value 7070b
Event: time 1474009072.178245, -------------- SYN_REPORT ------------
User LED
Input: None
Output: Script switches User LED ON and OFF in one second intervals
root@imx6-openrexultra:~#
for LED in /sys/devices/soc0/leds*/leds/*
do
echo Testing ${LED}
echo -n "1" > ${LED}/brightness
sleep 1
echo -n "0" > ${LED}/brightness
sleep 1
done
Input: None
Output: User LED is set to heartbeat blinking sequence
root@imx6-openrexultra:~# echo -n "heartbeat" > /sys/devices/soc0/leds*/leds/module-led/trigger
SD Activity LED
Input: None
Output: SD activity LED is set to show the status of SD card interface
root@imx6-openrexultra:~# echo -n "mmc1" > /sys/devices/soc0/leds*/leds/sd-activity-led/trigger
Microcontroller LPC1347
Input: LPC1347 firmware
Output: MCU program is executed and LED starts blinking
root@imx6-openrexultra:~# openrex-isp-handler.sh lpc/LPC1347-userLED.bin
ISP low
RST low
RST high
lpc21isp version 1.97
File lpc/LPC1347-userLED.bin:
loaded...
image size : 1068
Image size : 1068
Synchronizing (ESC to abort). OK
Read bootcode version: 2
5
Read part ID: LPC1345, 32 kiB FLASH / 8 kiB SRAM (0x28010541)
Will start programming at Sector 1 if possible, and conclude with Sector 0 to ensure that checksum is written last.
Erasing sector 0 first, to invalidate checksum. OK
Sector 0: ..........................
Download Finished... taking 0 seconds
Now launching the brand new code
RST low
ISP high
RST high
DDR memory
Input: None
Output: Memory test passes without any errors
<syntaxhighlight lang="bash">
root@imx6-openrexultra:~# memtester 2G 1
memtester version 4.1.3 (32-bit)
Copyright (C) 2010 Charles Cazabon.
Licensed under the GNU General Public License version 2 (only).
pagesize is 4096 pagesizemask is 0xfffff000 want 2048MB (2147483648 bytes) got 251MB (263602176 bytes), trying mlock ...locked. Loop 1/1:
Stuck Address : ok Random Value : ok Compare XOR : ok Compare SUB : ok Compare MUL : ok Compare DIV : ok Compare OR