Difference between revisions of "i.MX53 SODIMM PC Flashing images"
| Line 20: | Line 20: | ||
eth0.serverip=192.168.0.77 | eth0.serverip=192.168.0.77 | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | [[image:i.MX53_SODIMM_PC-Development_Kit-Network_settings. | + | [[image:i.MX53_SODIMM_PC-Development_Kit-Network_settings.png|580px]]<br /><br /> |
Erase NAND Flash memory: | Erase NAND Flash memory: | ||
| Line 26: | Line 26: | ||
erase /dev/nand0 | erase /dev/nand0 | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | [[image:i.MX53_SODIMM_PC-Development_Kit-Erising_NAND. | + | [[image:i.MX53_SODIMM_PC-Development_Kit-Erising_NAND.png|580px]]<br /><br /> |
Download bootloader image from TFTP server: | Download bootloader image from TFTP server: | ||
| Line 32: | Line 32: | ||
tftp vmx53/barebox.bin /dev/nand0.barebox.bb | tftp vmx53/barebox.bin /dev/nand0.barebox.bb | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | [[image:i.MX53_SODIMM_PC-Development_Kit-Loading_Barebox. | + | [[image:i.MX53_SODIMM_PC-Development_Kit-Loading_Barebox.png|580px]]<br /><br /> |
Power off the board and disconnect the JTAG cable as it is not needed anymore. Switch the module to the normal boot mode by changing H902 jumper on the base board (short pins 2 and 3 together):<br /> | Power off the board and disconnect the JTAG cable as it is not needed anymore. Switch the module to the normal boot mode by changing H902 jumper on the base board (short pins 2 and 3 together):<br /> | ||
| Line 38: | Line 38: | ||
Power on the board. The module boots from the new Barebox stored in its memory:<br /> | Power on the board. The module boots from the new Barebox stored in its memory:<br /> | ||
| − | [[image:i.MX53_SODIMM_PC-Development_Kit-Barebox_booting. | + | [[image:i.MX53_SODIMM_PC-Development_Kit-Barebox_booting.png|580px]]<br /><br /> |
== Flashing Linux kernel == | == Flashing Linux kernel == | ||
| Line 48: | Line 48: | ||
update barebox tftp vmx53/barebox-2012.09.0-vmx53-vpac2.bin | update barebox tftp vmx53/barebox-2012.09.0-vmx53-vpac2.bin | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | [[image:i.MX53_SODIMM_PC-Development_Kit-Updating_kernel. | + | [[image:i.MX53_SODIMM_PC-Development_Kit-Updating_kernel.png|580px]]<br /><br /> |
Restore bootloader environment to the default state and reset the board afterwards: | Restore bootloader environment to the default state and reset the board afterwards: | ||
| Line 54: | Line 54: | ||
erase /dev/nand0.bareboxenv | erase /dev/nand0.bareboxenv | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | [[image:i.MX53_SODIMM_PC-Development_Kit-Erasing_kernel. | + | [[image:i.MX53_SODIMM_PC-Development_Kit-Erasing_kernel.png|580px]]<br /><br /> |
Update Linux image (using the latest official Voipac image is highly recommended): | Update Linux image (using the latest official Voipac image is highly recommended): | ||
| Line 61: | Line 61: | ||
update kernel tftp vmx53/zImage-3.12.13_vmx53_20151129.bin | update kernel tftp vmx53/zImage-3.12.13_vmx53_20151129.bin | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | [[image:i.MX53_SODIMM_PC-Development_Kit-Flashing_kernel. | + | [[image:i.MX53_SODIMM_PC-Development_Kit-Flashing_kernel.png|580px]]<br /><br /> |
== Flashing filesystem == | == Flashing filesystem == | ||
Revision as of 20:15, 31 August 2021
This section describes flashing Barebox, Linux kernel and filesystem images.
If module could not start loading Barebox from its memory, recover bootloader by following these steps first.
Flashing bootloader
Enable serial boot mode by placing a link between pins 1 and 2 of H902 (BOOTMODE) header:
Make sure FTFP server is up and running. Download the latest image and store it into the TFTP directory.
A local network without DHCP control is recommended. Define network parameters for this network first:
eth0.ipaddr=192.168.0.154 eth0.netmask=255.255.255.0 eth0.gateway=192.168.0.1 eth0.serverip=192.168.0.77
Erase NAND Flash memory:
erase /dev/nand0
Download bootloader image from TFTP server:
tftp vmx53/barebox.bin /dev/nand0.barebox.bb
Power off the board and disconnect the JTAG cable as it is not needed anymore. Switch the module to the normal boot mode by changing H902 jumper on the base board (short pins 2 and 3 together):
Power on the board. The module boots from the new Barebox stored in its memory:
Flashing Linux kernel
Download the latest kernel image and store into the TFTP directory.
Before loading the image, set the server address and update the bootloader:
eth0.serverip=192.168.0.77 update barebox tftp vmx53/barebox-2012.09.0-vmx53-vpac2.bin
Restore bootloader environment to the default state and reset the board afterwards:
erase /dev/nand0.bareboxenv
Update Linux image (using the latest official Voipac image is highly recommended):
#update kernel tftp vmx53/zImage-2.6.35.3-vmx53-vpac0.bin update kernel tftp vmx53/zImage-3.12.13_vmx53_20151129.bin
Flashing filesystem
Download the latest filesystem and store into the TFTP directory.
Update the stored filesystem image:
update rootfs tftp vmx53/rootfs-ubifs-bb-1-18-vmx53-vpac0.bin
Reset the board. The module boots with newly downloaded files. The default vmx53 login is root without set password: 600px
