Difference between revisions of "iMX6 TinyRex USB Booting"
Jump to navigation
Jump to search
| (7 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | [[Category:iMX6 TinyRex Development | + | [[Category:iMX6 TinyRex Development Kit]] |
[[Category:iMX6 TinyRex Recovery]] | [[Category:iMX6 TinyRex Recovery]] | ||
<!-- --> | <!-- --> | ||
| − | These steps | + | These steps guide through loading a bootloader via USB OTG interface. This can be useful during recovery or bootloader update. |
''''' Recommended HW: ''''' | ''''' Recommended HW: ''''' | ||
| Line 11: | Line 11: | ||
''''' Recommended SW: ''''' | ''''' Recommended SW: ''''' | ||
| − | * [http://downloads.voipac.com/ | + | * [http://downloads.voipac.com/files/iMX6_TinyRex_Development_Kit/tools/mfgtools-Imx6Rex.zip MfgTool] feature |
* Serial line terminal | * Serial line terminal | ||
== Procedure == | == Procedure == | ||
| − | Connect USB cable to USB port on your computer and Development Kit USB OTG port.<br /> | + | Connect USB cable to USB port on your computer and Development Kit USB OTG port.<br /><br /> |
Short BOOT_MODE jumper on iMX6 TinyRex Base Board and power on the board:<br /> | Short BOOT_MODE jumper on iMX6 TinyRex Base Board and power on the board:<br /> | ||
| − | [[image: | + | [[image:iMX6_TinyRex_Development_Kit-Boot_mode_USB.jpg|300px]]<br /><br /> |
| − | Open an appropriate BAT file: | + | Open an appropriate BAT file:<br /> |
| − | [[image: | + | [[image:iMX6_TinyRex_Development_Kit-Boot-file-selection.png|580px]]<br /><br /> |
| − | Execute Manufacturing toolkit at host PC: | + | Execute Manufacturing toolkit at host PC:<br /> |
| − | [[image: | + | [[image:iMX6_TinyRex_Development_Kit-MfgTool_start.png|580px]]<br /><br /> |
| − | Press Start button (CPU will boot firmware loaded over USB): | + | Press Start button (CPU will boot firmware loaded over USB):<br /> |
| − | [[image: | + | [[image:iMX6_TinyRex_Development_Kit-MfgTool_progress.png|400px]]<br /><br /> |
| − | Wait until firmware transfer is finished | + | Wait until firmware transfer is finished:<br /> |
| − | [[image: | + | [[image:iMX6_TinyRex_Development_Kit-MfgTool_finished.png|400px]]<br /><br /> |
| − | The board boots using the firmware loaded over USB: | + | The board boots using the firmware loaded over USB:<br /> |
| − | [[image: | + | [[image:iMX6_TinyRex_Development_Kit-Serial_output.png|580px]] |
Latest revision as of 21:34, 26 October 2021
These steps guide through loading a bootloader via USB OTG interface. This can be useful during recovery or bootloader update.
Recommended HW:
- PC with USB port
- Voipac iMX6 TinyRex Development Kit
- USB to Micro-USB cable
Recommended SW:
- MfgTool feature
- Serial line terminal
Procedure
Connect USB cable to USB port on your computer and Development Kit USB OTG port.
Short BOOT_MODE jumper on iMX6 TinyRex Base Board and power on the board:
Open an appropriate BAT file:
Execute Manufacturing toolkit at host PC:
Press Start button (CPU will boot firmware loaded over USB):
Wait until firmware transfer is finished:
The board boots using the firmware loaded over USB:
