Difference between revisions of "i.MX25 SODIMM PC Boot device options"
| (One intermediate revision by the same user not shown) | |||
| Line 13: | Line 13: | ||
[[image:i.MX25_SODIMM_PC-Development_Kit-Boot_options.png|800px]]<br /><br /> | [[image:i.MX25_SODIMM_PC-Development_Kit-Boot_options.png|800px]]<br /><br /> | ||
| − | Boot configuration resistors can be located in [http://downloads.voipac.com/files/i.MX25_SODIMM_PC- | + | Boot configuration resistors can be located in [http://downloads.voipac.com/files/i.MX25_SODIMM_PC-Development_Kit/module/documents/i.MX25_SODIMM_Module-Assembly_drawings.pdf the board assembly drawing].<br /><br /> |
The procedure described below requires extra care as the faulty E-Fuses will cause permanent module malfunction. | The procedure described below requires extra care as the faulty E-Fuses will cause permanent module malfunction. | ||
<br /><br /> | <br /><br /> | ||
| − | BE AWARE THAT E-FUSES PROGRAMMING IS NON REVERSAL PROCESS! WARRANTY CLAIM CAUSED BY IMPROPER E-FUSES PROGRAMMING WILL NOT BE ACCEPTED! | + | '''''BE AWARE THAT E-FUSES PROGRAMMING IS NON REVERSAL PROCESS!<br>WARRANTY CLAIM CAUSED BY IMPROPER E-FUSES PROGRAMMING WILL NOT BE ACCEPTED!''''' |
=== Programming E-Fuses === | === Programming E-Fuses === | ||
Latest revision as of 18:25, 23 April 2022
Voipac i.MX25 SODIMM PC - Development Kit is delivered with E-Fuses left intact by default, not programmed. Booting can be selected from various devices thus allowing all the possible options to be tested.
Modules support multiple booting options:
- NAND Flash
- microSD/MMC
- SPI Flash
- I2C EEPROM
All the configuration signals are tied to supply voltage using external pull-up resistors. These on-module resistors (R600 - R609) ensure that the default state is correctly initialized. More details can be found on page no. 6 of the schematic shipped with the development kit:
Boot configuration resistors can be located in the board assembly drawing.
The procedure described below requires extra care as the faulty E-Fuses will cause permanent module malfunction.
BE AWARE THAT E-FUSES PROGRAMMING IS NON REVERSAL PROCESS!
WARRANTY CLAIM CAUSED BY IMPROPER E-FUSES PROGRAMMING WILL NOT BE ACCEPTED!
Programming E-Fuses
Dumping factory E-Fuses configuration before programming:
barebox:/ md -b -s /dev/imx_iim_bank0 00000000: 10 10 00 00 01 00 00 02 2b 2b 80 00 02 d9 f4 b1 ........++...... 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Writing E-Fuses (example set also MAC address 00:01:02:03:04:05):
barebox:/ imx_iim_bank0.permanent_write_enable=1 barebox:/ mw -b -d /dev/imx_iim_bank0 0x1a+6 0 1 2 3 4 5 barebox:/ md -b -s /dev/imx_iim_bank0 00000000: 10 10 00 00 01 00 00 02 2b 2b 80 00 02 d9 f4 b1 ........++...... 00000010: 00 00 00 00 00 00 00 00 00 00 00 01 02 03 04 05 ................
More information about E-Fuse bank layout can be found in the official NXP documentation.