Difference between revisions of "iMX6 Rex Ultra Creating Bootable microSD Card"
Jump to navigation
Jump to search
| Line 12: | Line 12: | ||
''''' Recommended SW: ''''' | ''''' Recommended SW: ''''' | ||
* [http://downloads.voipac.com/files/iMX6_Rex_Development_kit/tools/USBWriter-1.3.zip USBWriter] | * [http://downloads.voipac.com/files/iMX6_Rex_Development_kit/tools/USBWriter-1.3.zip USBWriter] | ||
| − | * [http://downloads.voipac.com/files/iMX6_Rex_Development_kit/module/software/yocto/binaries/fsl-image-gui-imx6-rexultra-2. | + | * [http://downloads.voipac.com/files/iMX6_Rex_Development_kit/module/software/yocto/binaries/fsl-image-gui-imx6-rexultra-2.4.sdcard.gz Appropriate Image file] |
== Windows == | == Windows == | ||
| Line 32: | Line 32: | ||
mkdir -pv ~/workdir/imx6/rootfs/yocto | mkdir -pv ~/workdir/imx6/rootfs/yocto | ||
cd ~/workdir/imx6/rootfs/yocto | cd ~/workdir/imx6/rootfs/yocto | ||
| − | wget http://downloads.voipac.com/ | + | wget http://downloads.voipac.com/files/iMX6_Rex_Development_kit/module/software/yocto/binaries/fsl-image-gui-imx6-rexultra-2.4.sdcard.gz |
</syntaxhighlight> | </syntaxhighlight> | ||
=== Extracting binary files === | === Extracting binary files === | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | sudo dd if=fsl-image-gui-imx6-rexultra- | + | sudo dd if=fsl-image-gui-imx6-rexultra-2.1.sdcard of=/dev/mmcblk0 conv=sync bs=64K |
</syntaxhighlight> | </syntaxhighlight> | ||
or | or | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | gunzip -c fsl-image-gui-imx6-rexultra-2. | + | gunzip -c fsl-image-gui-imx6-rexultra-2.4.sdcard.gz | sudo dd of=/dev/mmcblk0 conv=sync bs=64K |
</syntaxhighlight> | </syntaxhighlight> | ||
Revision as of 22:33, 24 March 2021
On this page the recommended procedure for creating a micro SD card contained with the required firmware and software is shown here. Following example shows steps used for iMX6 Rex Ultra Module.
Recommended HW:
- PC with microSD port (or an external SD reader)
- microSD card
Recommended SW:
Windows
Using USBWriter feature
Open USBWriter. Browse source file (appropriate fsl-image). Select target device:
400px
Click on Write button and confirm the procedure:
400px
400px
Bootable microSD Card is now created and prepared for use:
400px
Linux
Downloading image
mkdir -pv ~/workdir/imx6/rootfs/yocto cd ~/workdir/imx6/rootfs/yocto wget http://downloads.voipac.com/files/iMX6_Rex_Development_kit/module/software/yocto/binaries/fsl-image-gui-imx6-rexultra-2.4.sdcard.gz
Extracting binary files
sudo dd if=fsl-image-gui-imx6-rexultra-2.1.sdcard of=/dev/mmcblk0 conv=sync bs=64K
or
gunzip -c fsl-image-gui-imx6-rexultra-2.4.sdcard.gz | sudo dd of=/dev/mmcblk0 conv=sync bs=64K