Difference between revisions of "iMX6 Rex USB Booting"
Jump to navigation
Jump to search
(Created page with "Category:iMX6 Rex Development kit Category:iMX6 Rex Recovery <!-- --> These steps guides through loading a bootloader via USB OTG interface. This can be useful during...") |
|||
| Line 16: | Line 16: | ||
== Procedure == | == Procedure == | ||
| − | Resolder resistors R0 on position R63 to R62 and R67 to R65 on the base board (Near battery holder J32): | + | Resolder resistors R0 on position R63 to R62 and R67 to R65 on the base board (Near battery holder J32):<br /> |
[[image:iMX6_Rex_Development_kit-USB_OTG_selection.jpg|450px]]<br /><br /> | [[image:iMX6_Rex_Development_kit-USB_OTG_selection.jpg|450px]]<br /><br /> | ||
| − | Short BOOT_MODE jumper JP2 on iMX6 Rex Base Board. Connect PC and USB OTG port with a USB cable and power on the base board: | + | Short BOOT_MODE jumper JP2 on iMX6 Rex Base Board. Connect PC and USB OTG port with a USB cable and power on the base board:<br /> |
[[image:iMX6_Rex_Development_kit-USB_OTG_jumper.jpg|300px]]<br /><br /> | [[image:iMX6_Rex_Development_kit-USB_OTG_jumper.jpg|300px]]<br /><br /> | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Open an appropriate BAT file:<br /> | Open an appropriate BAT file:<br /> | ||
| − | [[image: | + | [[image:iMX6_Rex_Development_kit-Boot-file-selection.jpg|300px]]<br /><br /> |
Execute Manufacturing toolkit at host PC:<br /> | Execute Manufacturing toolkit at host PC:<br /> | ||
| − | [[image: | + | [[image:iMX6_Rex_Development_kit-MfgTool_start.jpg|600px]]<br /><br /> |
Press Start button (CPU will boot firmware loaded over USB):<br /> | Press Start button (CPU will boot firmware loaded over USB):<br /> | ||
| − | [[image: | + | [[image:iMX6_Rex_Development_kit-MfgTool_progress.jpg|400px]]<br /><br /> |
Wait until firmware transfer is finished:<br /> | Wait until firmware transfer is finished:<br /> | ||
| − | [[image: | + | [[image:iMX6_Rex_Development_kit-MfgTool_finished.jpg|400px]]<br /><br /> |
The board boots using the firmware loaded over USB:<br /> | The board boots using the firmware loaded over USB:<br /> | ||
| − | [[image: | + | [[image:iMX6_Rex_Development_kit-Serial_output.jpg|600px]] |
Revision as of 01:09, 20 March 2021
These steps guides through loading a bootloader via USB OTG interface. This can be useful during recovery or bootloader update.
Recommended HW:
- PC with USB port
- Voipac iMX6 Rex Development Kit
- USB to Micro-USB cable
- Soldering station
Recommended SW:
- MfgTool feature
- Serial line terminal
Procedure
Resolder resistors R0 on position R63 to R62 and R67 to R65 on the base board (Near battery holder J32):
450px
Short BOOT_MODE jumper JP2 on iMX6 Rex Base Board. Connect PC and USB OTG port with a USB cable and power on the base board:
300px
Open an appropriate BAT file:
300px
Execute Manufacturing toolkit at host PC:
600px
Press Start button (CPU will boot firmware loaded over USB):
400px
Wait until firmware transfer is finished:
400px
The board boots using the firmware loaded over USB:
600px
