Difference between revisions of "i.MX25 SODIMM PC Flashing images"
Jump to navigation
Jump to search
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | [[Category:i.MX25 SODIMM PC - Development | + | [[Category:i.MX25 SODIMM PC - Development Kit]] |
[[Category:i.MX25 SODIMM PC Recovery]] | [[Category:i.MX25 SODIMM PC Recovery]] | ||
<!-- --> | <!-- --> | ||
| Line 9: | Line 9: | ||
== Preparing for files transfer == | == Preparing for files transfer == | ||
Make sure FTFP server is up and running. Download the latest images and store them into the TFTP directory: | Make sure FTFP server is up and running. Download the latest images and store them into the TFTP directory: | ||
| − | * [http://downloads.voipac.com/files/i.MX25_SODIMM_PC- | + | * [http://downloads.voipac.com/files/i.MX25_SODIMM_PC-Development_Kit/module/software/barebox/binaries/old/barebox-2012.09.0-vmx25-vpac4.bin Barebox image] |
| − | * [http://downloads.voipac.com/files/i.MX25_SODIMM_PC- | + | * [http://downloads.voipac.com/files/i.MX25_SODIMM_PC-Development_Kit/module/software/linux/binaries/old/zImage-2.6.35-vmx25-vpac9.bin Linux kernel binary] |
| − | * [http://downloads.voipac.com/files/i.MX25_SODIMM_PC- | + | * [http://downloads.voipac.com/files/i.MX25_SODIMM_PC-Development_Kit/module/software/filesystem/binaries/rootfs-ubifs-bb-1-18-vmx25-vpac0.bin Filesystem image] |
<br /> | <br /> | ||
A local network without DHCP control is recommended. Define network parameters for this network first: | A local network without DHCP control is recommended. Define network parameters for this network first: | ||
| Line 20: | Line 20: | ||
eth0.serverip=192.168.0.77 | eth0.serverip=192.168.0.77 | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | [[image:i.MX25_SODIMM_PC-Development_Kit-Network_settings. | + | [[image:i.MX25_SODIMM_PC-Development_Kit-Network_settings.png|580px]]<br /><br /> |
Erase NAND Flash memory: | Erase NAND Flash memory: | ||
| Line 26: | Line 26: | ||
erase /dev/nand0 | erase /dev/nand0 | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | [[image:i.MX25_SODIMM_PC-Development_Kit-Erasing_NAND. | + | [[image:i.MX25_SODIMM_PC-Development_Kit-Erasing_NAND.png|580px]]<br /><br /> |
== Downloading and flashing images == | == Downloading and flashing images == | ||
| Line 35: | Line 35: | ||
update rootfs tftp vmx25/rootfs-ubifs-bb-1-18-vmx25-vpac0.bins | update rootfs tftp vmx25/rootfs-ubifs-bb-1-18-vmx25-vpac0.bins | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | [[image:i.MX25_SODIMM_PC-Development_Kit-Updating_kernel. | + | [[image:i.MX25_SODIMM_PC-Development_Kit-Updating_kernel.png|580px]]<br /><br /> |
| − | + | During the NAND storage erasing process the MAC address was deleted as well. It is required to be set up again. The MAC address can be found on the sticker placed on the module (in format 00:0d:15:00:XX:XX).<br /><br /> | |
| − | |||
| − | Reset the board. The module boots with newly downloaded files. The default | + | Reset the board. The module boots with newly downloaded files. The default vmx25 login is '''root''' without set password: |
| − | [[image:i.MX25_SODIMM_PC-Development_Kit-Running_Linux. | + | [[image:i.MX25_SODIMM_PC-Development_Kit-Running_Linux.png|580px]] |
Latest revision as of 22:34, 8 December 2021
This section describes flashing Barebox, Linux kernel and filesystem images.
If module could not start loading Barebox from its memory, recover bootloader by following these steps first.
Preparing for files transfer
Make sure FTFP server is up and running. Download the latest images and store them into the TFTP directory:
A local network without DHCP control is recommended. Define network parameters for this network first:
eth0.ipaddr=192.168.0.150 eth0.netmask=255.255.255.0 eth0.gateway=192.168.0.1 eth0.serverip=192.168.0.77
Erase NAND Flash memory:
erase /dev/nand0
Downloading and flashing images
Load the firmware files:
update barebox tftp vmx25/barebox-2012.09.0-vmx25-vpac4.bin update kernel tftp vmx25/zImage-2.6.35-vmx25-vpac9.bin update rootfs tftp vmx25/rootfs-ubifs-bb-1-18-vmx25-vpac0.bins
During the NAND storage erasing process the MAC address was deleted as well. It is required to be set up again. The MAC address can be found on the sticker placed on the module (in format 00:0d:15:00:XX:XX).
Reset the board. The module boots with newly downloaded files. The default vmx25 login is root without set password:
