Difference between revisions of "TFT EDT Display Set"
Jump to navigation
Jump to search
| (10 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | [[Category:i.MX53 SODIMM PC - Development | + | [[Category:i.MX53 SODIMM PC - Development Kit]] |
| − | [[Category:i.MX51 SODIMM PC - Development | + | [[Category:i.MX51 SODIMM PC - Development Kit]] |
| − | [[Category:i.MX25 SODIMM PC - Development | + | [[Category:i.MX25 SODIMM PC - Development Kit]] |
<!-- --> | <!-- --> | ||
| − | This section shows information about TFT EDT | + | This section shows information about TFT EDT display. This multitouch capacitive display is assigned to be used with the i.MX53, i.MX51 and i.MX25 SODIMM PC - Development Kits. It is supported in OS Linux, Android and Qt4e. |
<br /><br /> | <br /><br /> | ||
| − | The display datasheet can be downloaded from [http://downloads.voipac.com/files/i.MX53_SODIMM_PC- | + | The display datasheet can be downloaded from [http://downloads.voipac.com/files/i.MX53_SODIMM_PC-Development_Kit/accessories/TFT_EDT_display_adapter/TFT_EDT_display-Datasheet.pdf here]. |
== Hardware connection == | == Hardware connection == | ||
| − | To make the physical connection between the board and the display easier, [http://downloads.voipac.com/files/i.MX53_SODIMM_PC- | + | To make the physical connection between the board and the display easier, [http://downloads.voipac.com/files/i.MX53_SODIMM_PC-Development_Kit/accessories/TFT_EDT_display_adapter/i.MX25_SODIMM_Base_Board-TFT_EDT_display_adapter-Schematic.pdf TFT EDT display adapter] was designed to connect the set together. |
[[image:i.MX25_SODIMM_Base_Board-TFT_EDT_display_adapter-Display_connection.jpg|800px]]<br /> | [[image:i.MX25_SODIMM_Base_Board-TFT_EDT_display_adapter-Display_connection.jpg|800px]]<br /> | ||
To implement the display capabilities, following connections need to be made: | To implement the display capabilities, following connections need to be made: | ||
| − | * TFT EDT display adapter is plugged into the Base Board H200 male | + | * TFT EDT display adapter is plugged into the Base Board H200 and H700 male headers. By using this two point connection, pin 1 cannot be plugged the wrong way. |
| − | * SPI control is established | + | * SPI control is established between adapter H2 header and H501 connector on the Base Board using four separate wires (see the picture below) |
| − | * A flexible flat cable is | + | * A flexible flat cable is plugged for all the connections between the adapter and the display |
[[image:i.MX25_SODIMM_Base_Board-TFT_EDT_display_adapter-Base_board_connection.jpg|800px]] | [[image:i.MX25_SODIMM_Base_Board-TFT_EDT_display_adapter-Base_board_connection.jpg|800px]] | ||
Latest revision as of 20:08, 26 November 2021
This section shows information about TFT EDT display. This multitouch capacitive display is assigned to be used with the i.MX53, i.MX51 and i.MX25 SODIMM PC - Development Kits. It is supported in OS Linux, Android and Qt4e.
The display datasheet can be downloaded from here.
Hardware connection
To make the physical connection between the board and the display easier, TFT EDT display adapter was designed to connect the set together.
To implement the display capabilities, following connections need to be made:
- TFT EDT display adapter is plugged into the Base Board H200 and H700 male headers. By using this two point connection, pin 1 cannot be plugged the wrong way.
- SPI control is established between adapter H2 header and H501 connector on the Base Board using four separate wires (see the picture below)
- A flexible flat cable is plugged for all the connections between the adapter and the display
