iMX6 Rex Environmental chamber testing

On this page environmental stress testing results of iMX6 Rex Development kit are displayed. Detailed instructions how to setup iMX6 Rex Development kit are also shown.

Hardware configuration

Following hardware configurations were used for the testing:

• 3x iMX6 Rex Development kit in Pro configuration
  • i.MX6 Quad 1.0 GHz CPU - extended temperature range (-20°C to +105°C)
  • 2GB DDR3 Memory (4x 4Gb DDR3 Memory chips) - commercial temperature range (0°C to +95°C)
  • 1GBps Ethernet PHY Tranciever KSZ9021RN - commercial temperature range (0°C to +70°C)

• 1x iMX6 Rex Development kit in modified Pro configuration
  • i.MX6 Quad 1.0 GHz CPU - extended temperature range (-20°C to +105°C)
  • 1GB DDR3 Memory (4x 2Gb DDR3 Memory chips) - commercial temperature range (0°C to +95°C)
  • 1GBps Ethernet PHY Tranciever KSZ9021RN - commercial temperature range (0°C to +70°C)

Note: During the chamber testing a heatsink covering the whole module was used. With a bigger heatsink, maximum operating temperature can be further extended.

The setup in environmental chamber:
800px

Test description

The main purpose of this test is to check memory stability of iMX6 Rex Module. During the test these threads will be running:

• 4 threads of extensive memory stress test
• 4 threads of CPU stress test

This is the main command used for the test:

stressapptest -s 600000 -M 768 -m 4 -C 4 -W --printsec 600 -l /home/ubuntu/testing-env-chamber/stressapptest.log

Detailed description about how to setup and run the whole test can be found in section How to prepare the test. It describes all the scripts and explains log files.

Testing Results

The picture below shows the temperature profile during the whole testing process:
800px

Switch ON/OFF test - PASS

Test description: Boards were switched OFF, left OFF for 10 minutes and then switched ON. These tests were done several times for temperatures between -30°C to -35°C and for a temperature +70°C. All the boards booted up successfully.

396px

396px

Running the boards at -25°C - PASS

Test description: Ambient temperature was set to -25°C and the CPU and Memory stress tests were running. 800px

Running the boards at +70°C - PASS

Test description: Ambient temperature was set to +70°C and the CPU and Memory stress tests were running. 800px

Fast change of the temperature (from -25°C to +70°C) - PASS

Test description: Ambient temperature was rapidly changed from -25°C to +70°C. The CPU and Memory stress tests were running.

Preparing the test

SD card setup

Linux 4.1 kernel was used for this test. Modified Xubuntu filesystem can be accessed from here. To create a new SD card, these instructions can be followed.

Create the log files

mkdir /home/ubuntu/testing-env-chamber
cd /home/ubuntu/testing-env-chamber
touch cpu-temp.log
touch stressapptest.log

Setup the cron

To be able to check the CPU temperature every minute a new cron job was setup. For Ubuntu file systems postfix package installation is required:

sudo apt-get install postfix

To setup a cron tab, the file containing all cron jobs needs to be altered. Before running the crontab for the first time, selecting a text editor is required:

sudo crontab -e

Paste the following line to the end of the cron list file. The output time format will be set the same as for stressapptest. Cron job performs a current CPU temperature readout and the data are saved in the log file:

* * * * * { echo -n $(date +\%Y/\%m/\%d-\%T); echo -n "("; echo -n $(date +\%Z); echo -n ") "; cat /sys/devices/virtual/thermal/thermal_zone0/temp; } >> /home/ubuntu/testing-env-chamber/cpu-temp.log

Note: The percent sign '%' has a special purpose in the cron file. As this sign is needed to write the date formats, the backslash is required to be placed before the percent sign: '\%'.

Setup the SSH connections

During the testing a simple local Ethernet network utilising a LAN switch and a control laptop was created. Two SSH sessions per board were opened (8 sessions in total). The first session was used for CPU and memory stress test. In the window below the current CPU temperature was printed out. The other three boards used the same format: 800px

Set up the date

As the RTC clock was not used during the test, the current time is set after boards boot up. A time zone is updated first:

ln -sf /usr/share/zoneinfo/Europe/Bratislava /etc/localtime

The actual time is changed afterwards. Sequence of digits in the following order was used: month day hour minute year. The command below sets this time and date: 04-July-2014 08:26

date 070408262014

Setup the CPU temperature printout

Before the CPU and memory stress tests start, the old logs were backed up:

cd /home/ubuntu/testing-env-chamber
mv cpu-temp.log cpu-temp-testing1.log
mv stressapptest.log stressapptest-testing1.log
touch cpu-temp.log
touch stressapptest.log

Tail command is used to read the temperature. It displays the last part of files (the cron job is writing to this log file):

tail -F cpu-temp.log

Start the stress test

stressapptest -s 600000 -M 768 -m 4 -C 4 -W --printsec 600 -l /home/ubuntu/testing-env-chamber/stressapptest.log

To make sure test is running smoothly, potential errors can be found in the log file (instead of rolling the stress test printout):

grep -i "error" stressapptest.log

The original article can be accessed on the iMX6Rex.com website.