iMX6 TinyRex Camera - Revision history

Voipac at 08:08, 24 April 2022

2022-04-24T08:08:33Z

2021-10-23T21:23:32Z

2021-03-15T10:55:36Z

2021-03-14T13:32:06Z

2021-03-14T13:31:23Z

2021-03-14T13:30:32Z

2021-03-14T13:29:53Z

2021-03-14T13:29:00Z

2021-03-14T13:23:29Z

2021-03-14T13:22:40Z

@@ Line 4: / Line 4: @@
 <div style="float:right">__TOC__</div>
-This example uses Raspberry Pi Camera Rev 1.3 (build on OV5647 MIPI sensor) as a test device for CSI Interface. On this page OV5647 sensor integration, settings and usage on i.MX6 processors are shown.<br /><br />
+This example uses Raspberry Pi Camera Rev 1.3 (built on OV5647 MIPI sensor) as a test device for CSI Interface. On this page OV5647 sensor integration, settings and usage on i.MX6 processors are shown.<br /><br />
 '''''Note:''''' There is an issue concerning Raspberry Pi 1.3 cameras and its I2C detected. There might be some camera models that does not get identified.

@@ Line 1: / Line 1: @@
-[[Category:iMX6 TinyRex Development kit]]
+[[Category:iMX6 TinyRex Development Kit]]
 [[Category:iMX6 TinyRex Peripherals]]
 <!-- -->

@@ Line 6: / Line 6: @@
 This example uses Raspberry Pi Camera Rev 1.3 (build on OV5647 MIPI sensor) as a test device for CSI Interface. On this page OV5647 sensor integration, settings and usage on i.MX6 processors are shown.<br /><br />
-'''''Note:''''' There is an issue concerning Raspberry Pi 1.3 cameras and its I2C detected. There might be some models that does not get identified.
+'''''Note:''''' There is an issue concerning Raspberry Pi 1.3 cameras and its I2C detected. There might be some camera models that does not get identified.
 == Device detection ==

@@ Line 119: / Line 119: @@
 </syntaxhighlight>
-=== 640x480 (narrow angle of view)
+=== 640x480 (narrow angle of view) ===
 <syntaxhighlight lang="bash">
 echo 6 > /sys/bus/i2c/devices/1-0036/ov5647_mode

@@ Line 88: / Line 88: @@
 </syntaxhighlight>
-== Resolution change ==
+== Resolution setting ==
 === 1280x960 ===
 <syntaxhighlight lang="bash">

@@ Line 55: / Line 55: @@
 </syntaxhighlight>
-== Modules ==
+== Modules listing ==
 === Kernel 4.1 ===
 <syntaxhighlight lang="bash">

@@ Line 44: / Line 44: @@
 GPIO pins are controlled by the camera driver and access to these pins is blocked. Power on signal is recognised as GPIO 74, LED GPIO has number 54.<br /><br />
-LED located on camera module can be tested by temporarily disabling mipi kernel module and setting and tooling corresponding GPIO pin:
+LED located on camera module can be tested by temporarily disabling mipi kernel module and toggling corresponding GPIO pin:
 <syntaxhighlight lang="bash">
 root@imx6s-tinyrex:~# modprobe -r ov5647_camera_mipi

@@ Line 42: / Line 42: @@
 == GPIO control ==
-GPIO pins are controlled by the camera driver and access to this pins is blocked. Power on GPIO is 74, LED GPIO has number 54.
+GPIO pins are controlled by the camera driver and access to these pins is blocked. Power on GPIO is 74, LED GPIO has number 54.
 <syntaxhighlight lang="bash">
 root@imx6s-tinyrex:~# modprobe -r ov5647_camera_mipi