iMX6 Rex 5V power supply modifications - Revision history

Voipac at 21:52, 26 October 2021

2021-10-26T21:52:10Z

2021-10-26T21:51:44Z

2021-10-24T20:40:28Z

2021-03-23T11:49:10Z

2021-03-22T07:07:30Z

2021-03-22T06:58:45Z

2021-03-22T06:58:34Z

2021-03-22T06:58:06Z

2021-03-22T06:56:56Z

2021-03-22T06:55:46Z

@@ Line 30: / Line 30: @@
 == iMX6 Rex Module ==
 {|
-| [[image:iMX6_Rex_Development_kit-PMIC.jpg|100px]]
+| [[image:iMX6_Rex_Development_Kit-PMIC.jpg|100px]]
 | style="vertical-align:top;" |  '''''Note:''''' It is required that the power management unit ISL6236AIRZ is fitted on positions U11 and U13
 |}

@@ Line 7: / Line 7: @@
 == iMX6 Rex Base Board ==
 {|
-| [[image:iMX6_Rex_Development_kit-PMIC.jpg|100px]]
+| [[image:iMX6_Rex_Development_Kit-PMIC.jpg|100px]]
 | style="vertical-align:top;" |  '''''Note:''''' It is required that the power management unit ISL6236AIRZ is fitted on position U22
 |}
@@ Line 24: / Line 24: @@
 <br /><br />
 {|
-| [[image:iMX6_Rex_Development_kit-ATX_connector.jpg|200px]]
+| [[image:iMX6_Rex_Development_Kit-ATX_connector.jpg|200px]]
 | style="vertical-align:top;" |  '''''Note:''''' To power the board, ATX connector (position J38) usage is recommended
 |}

@@ Line 1: / Line 1: @@
-[[Category:iMX6 Rex Development kit]]
+[[Category:iMX6 Rex Development Kit]]
 <!-- -->
 <div style="float:right">__TOC__</div>
-This procedure shows how to modify iMX6 Rex Development kit to support 5V power supply.
+This procedure shows how to modify iMX6 Rex Development Kit to support 5V power supply.
 == iMX6 Rex Base Board ==

@@ Line 18: / Line 18: @@
 '''''Important:''''' It is recommended to test the base board without the module first:
-* Measure the input voltage + VIN is set to 5 Volts.
+* Set up and double check the input voltage + VIN to 5 Volts.
-* Other voltage rails voltages are set as described in the schematic
+* Measure other voltage rails if they are set as described in the schematic
-* Check if the upper green POK LED diode in position D18 is on (all sources are turned on the iMX6 Rex Base Board)
+* The upper green POK LED diode in position D18 should be on (all sources are turned on the iMX6 Rex Base Board)
 <br /><br />

@@ Line 20: / Line 20: @@
 * Measure the input voltage + VIN is set to 5 Volts.
 * Other voltage rails voltages are set as described in the schematic
-* Check if an upper green POK LED light on position D18 is on (all sources are turned on the iMX6 Rex Base Board)
+* Check if the upper green POK LED diode in position D18 is on (all sources are turned on the iMX6 Rex Base Board)
 <br /><br />

@@ Line 8: / Line 8: @@
 {|
 | [[image:iMX6_Rex_Development_kit-PMIC.jpg|100px]]
-| style="vertical-align:top;" |'''''Note:''''' It is required that the power management unit ISL6236AIRZ is fitted on position U22<br />
+| style="vertical-align:top;" |  '''''Note:''''' It is required that the power management unit ISL6236AIRZ is fitted on position U22<br />
 |}
@@ Line 26: / Line 26: @@
 == iMX6 Rex Module ==
-'''''Note:''''' It is required that the power management unit ISL6236AIRZ is fitted on positions U11 and U13<br />
+{|
-[[image:iMX6_Rex_Development_kit-PMIC.jpg|100px]]
+| [[image:iMX6_Rex_Development_kit-PMIC.jpg|100px]]
 === Bottom side modifications ===
 [[image:iMX6_Rex_Module-5V_modification_bottom.jpg|800px]]